Windows XP Crash

[Guest]

Please help anybody!
My laptop crashed yesterday. and it want open windows.
It is askink for msgina.dll and to notify administrator, asking for restart
adn this again and again.
Copied the file on a disk from my big computer, but how can I feed it in now?
Can`t fin also no feature to make a start up copy to try this.
Have the original WinXP CD but it doesn`t work either.
Pleas help somebody
Thank you
Ursula

 

[Guest]

1. Boot to Recovery Console.

2 . type the following commands
cd system32 [enter]

ren winlogon.exe winlogon.old
ren msgina.dll msgina.old
ren shell32.dll shell32.old
ren shlwapi.dll shlwapi.old

cd.. [enter]
cd servicepackfiles\i386 [enter]
copy MSGINA.DLL c:\windows\system32
copy SHELL32.DLL c:\windows\system32
copy WINLOGON.EXE c:\windows\system32
copy shlwapi.dll c:\windows\system32

if not there, expand from the cd

3 Type EXIT and hit enter

 

[Daave]

Additionally, Ursula, you need to make sure you boot off the CD. You
should access your BIOS setup *before* the PC attempts to boot off your
hard drive, then configure it to boot off the CD, then you should be
fine. See http://www.michaelstevenstech.com/bios_manufacturer.htm for
how to do this.

At this point, you should be able to use the Recovery Console from your
installation CD.

(Do you have an installation CD? Or is it a different type of "WinXP
CD"?)

1. Boot to Recovery Console.

2 . type the following commands
cd system32 [enter]

ren winlogon.exe winlogon.old
ren msgina.dll msgina.old
ren shell32.dll shell32.old
ren shlwapi.dll shlwapi.old

cd.. [enter]
cd servicepackfiles\i386 [enter]
copy MSGINA.DLL c:\windows\system32
copy SHELL32.DLL c:\windows\system32
copy WINLOGON.EXE c:\windows\system32
copy shlwapi.dll c:\windows\system32

if not there, expand from the cd

3 Type EXIT and hit enter

Please help anybody!
My laptop crashed yesterday. and it want open windows.
It is askink for msgina.dll and to notify administrator, asking for
restart adn this again and again.
Copied the file on a disk from my big computer, but how can I feed
it in now? Can`t fin also no feature to make a start up copy to try
this.
Have the original WinXP CD but it doesn`t work either.
Pleas help somebody
Thank you
Ursula

 

[Guest]

on console i get until end of #2 the following command is not possible.
Now the second time it tells me the rem command is not recognized.
eithrt is the cd..

Additionally, Ursula, you need to make sure you boot off the CD. You
should access your BIOS setup *before* the PC attempts to boot off your
hard drive, then configure it to boot off the CD, then you should be
fine. See http://www.michaelstevenstech.com/bios_manufacturer.htm for
how to do this.

At this point, you should be able to use the Recovery Console from your
installation CD.

(Do you have an installation CD? Or is it a different type of "WinXP
CD"?)

1. Boot to Recovery Console.

2 . type the following commands
cd system32 [enter]

ren winlogon.exe winlogon.old
ren msgina.dll msgina.old
ren shell32.dll shell32.old
ren shlwapi.dll shlwapi.old

cd.. [enter]
cd servicepackfiles\i386 [enter]
copy MSGINA.DLL c:\windows\system32
copy SHELL32.DLL c:\windows\system32
copy WINLOGON.EXE c:\windows\system32
copy shlwapi.dll c:\windows\system32

if not there, expand from the cd

3 Type EXIT and hit enter

Please help anybody!
My laptop crashed yesterday. and it want open windows.
It is askink for msgina.dll and to notify administrator, asking for
restart adn this again and again.
Copied the file on a disk from my big computer, but how can I feed
it in now? Can`t fin also no feature to make a start up copy to try
this.
Have the original WinXP CD but it doesn`t work either.
Pleas help somebody
Thank you
Ursula

 

[Guest]

Got the thing with the cd.. wrong, did not put the space in .
My Problem now is to get the CD-Rom working to copy.
When I go down it shows the D:\ comes but back to C:\ ...
Thanks if you can help me here out
Ursula

on console i get until end of #2 the following command is not possible.
Now the second time it tells me the rem command is not recognized.
eithrt is the cd..

Additionally, Ursula, you need to make sure you boot off the CD. You
should access your BIOS setup *before* the PC attempts to boot off your
hard drive, then configure it to boot off the CD, then you should be
fine. See http://www.michaelstevenstech.com/bios_manufacturer.htm for
how to do this.

At this point, you should be able to use the Recovery Console from your
installation CD.

(Do you have an installation CD? Or is it a different type of "WinXP
CD"?)

1. Boot to Recovery Console.

2 . type the following commands
cd system32 [enter]

ren winlogon.exe winlogon.old
ren msgina.dll msgina.old
ren shell32.dll shell32.old
ren shlwapi.dll shlwapi.old

cd.. [enter]
cd servicepackfiles\i386 [enter]
copy MSGINA.DLL c:\windows\system32
copy SHELL32.DLL c:\windows\system32
copy WINLOGON.EXE c:\windows\system32
copy shlwapi.dll c:\windows\system32

if not there, expand from the cd

3 Type EXIT and hit enter


:

Please help anybody!
My laptop crashed yesterday. and it want open windows.
It is askink for msgina.dll and to notify administrator, asking for
restart adn this again and again.
Copied the file on a disk from my big computer, but how can I feed
it in now? Can`t fin also no feature to make a start up copy to try
this.
Have the original WinXP CD but it doesn`t work either.
Pleas help somebody
Thank you
Ursula

 

[Daave]

We overlooked something! See:

"Logon User Interface DLL Msgina.dll failed to load" error message after
you install the MS04-003 security update"
http://support.microsoft.com/kb/836683

Got the thing with the cd.. wrong, did not put the space in .
My Problem now is to get the CD-Rom working to copy.
When I go down it shows the D:\ comes but back to C:\ ...
Thanks if you can help me here out
Ursula

on console i get until end of #2 the following command is not
possible.
Now the second time it tells me the rem command is not recognized.
eithrt is the cd..

Additionally, Ursula, you need to make sure you boot off the CD.
You
should access your BIOS setup *before* the PC attempts to boot off
your
hard drive, then configure it to boot off the CD, then you should
be
fine. See http://www.michaelstevenstech.com/bios_manufacturer.htm
for
how to do this.

At this point, you should be able to use the Recovery Console from
your
installation CD.

(Do you have an installation CD? Or is it a different type of
"WinXP
CD"?)


WindowsXPert wrote:
1. Boot to Recovery Console.

2 . type the following commands
cd system32 [enter]

ren winlogon.exe winlogon.old
ren msgina.dll msgina.old
ren shell32.dll shell32.old
ren shlwapi.dll shlwapi.old

cd.. [enter]
cd servicepackfiles\i386 [enter]
copy MSGINA.DLL c:\windows\system32
copy SHELL32.DLL c:\windows\system32
copy WINLOGON.EXE c:\windows\system32
copy shlwapi.dll c:\windows\system32

if not there, expand from the cd

3 Type EXIT and hit enter


:

Please help anybody!
My laptop crashed yesterday. and it want open windows.
It is askink for msgina.dll and to notify administrator, asking
for
restart adn this again and again.
Copied the file on a disk from my big computer, but how can I
feed
it in now? Can`t fin also no feature to make a start up copy to
try
this.
Have the original WinXP CD but it doesn`t work either.
Pleas help somebody
Thank you
Ursula

 

[Guest]

I'm pretty sure that article takes you through a process similar (if not
identical) to the one in my earlier post.

By the way, the command you were having a problem with earlier --is REN
(R-E-N) *not* REM (R-E-M). In a batch file, "REM" means "Remark" and the
command processor ignores everything which follows until the next [ENTER]
character appears. REN (R-E-N) is short for RENAME, which you can type all
the way out, if you wish.

Hope this helps.

Sam French

We overlooked something! See:

"Logon User Interface DLL Msgina.dll failed to load" error message after
you install the MS04-003 security update"
http://support.microsoft.com/kb/836683

Got the thing with the cd.. wrong, did not put the space in .
My Problem now is to get the CD-Rom working to copy.
When I go down it shows the D:\ comes but back to C:\ ...
Thanks if you can help me here out
Ursula

on console i get until end of #2 the following command is not
possible.
Now the second time it tells me the rem command is not recognized.
eithrt is the cd..

:

Additionally, Ursula, you need to make sure you boot off the CD.
You
should access your BIOS setup *before* the PC attempts to boot off
your
hard drive, then configure it to boot off the CD, then you should
be
fine. See http://www.michaelstevenstech.com/bios_manufacturer.htm
for
how to do this.

At this point, you should be able to use the Recovery Console from
your
installation CD.

(Do you have an installation CD? Or is it a different type of
"WinXP
CD"?)


WindowsXPert wrote:
1. Boot to Recovery Console.

2 . type the following commands
cd system32 [enter]

ren winlogon.exe winlogon.old
ren msgina.dll msgina.old
ren shell32.dll shell32.old
ren shlwapi.dll shlwapi.old

cd.. [enter]
cd servicepackfiles\i386 [enter]
copy MSGINA.DLL c:\windows\system32
copy SHELL32.DLL c:\windows\system32
copy WINLOGON.EXE c:\windows\system32
copy shlwapi.dll c:\windows\system32

if not there, expand from the cd

3 Type EXIT and hit enter


:

Please help anybody!
My laptop crashed yesterday. and it want open windows.
It is askink for msgina.dll and to notify administrator, asking
for
restart adn this again and again.
Copied the file on a disk from my big computer, but how can I
feed
it in now? Can`t fin also no feature to make a start up copy to
try
this.
Have the original WinXP CD but it doesn`t work either.
Pleas help somebody
Thank you
Ursula

 

[Guest]

You are both too kind to help me out, thanks a lot!!!
I tried the article too, no help. I wrote the ren thing right in the console
and the names are changed. Puter couldn't find the msgina.dll but the others.
then I tried to go in from windows, but without the proper msgina no way. so
I tried to go to D:\ but puter went to D and right back to C:\. Tried every
letter to see, if its there (CD-ROM) but it told me no disk to find there (it
WAS in the player).
How can I find the CD on console?
Thanks again
Ursula

I'm pretty sure that article takes you through a process similar (if not
identical) to the one in my earlier post.

By the way, the command you were having a problem with earlier --is REN
(R-E-N) *not* REM (R-E-M). In a batch file, "REM" means "Remark" and the
command processor ignores everything which follows until the next [ENTER]
character appears. REN (R-E-N) is short for RENAME, which you can type all
the way out, if you wish.

Hope this helps.

Sam French

We overlooked something! See:

"Logon User Interface DLL Msgina.dll failed to load" error message after
you install the MS04-003 security update"
http://support.microsoft.com/kb/836683

Got the thing with the cd.. wrong, did not put the space in .
My Problem now is to get the CD-Rom working to copy.
When I go down it shows the D:\ comes but back to C:\ ...
Thanks if you can help me here out
Ursula




:

on console i get until end of #2 the following command is not
possible.
Now the second time it tells me the rem command is not recognized.
eithrt is the cd..

:

Additionally, Ursula, you need to make sure you boot off the CD.
You
should access your BIOS setup *before* the PC attempts to boot off
your
hard drive, then configure it to boot off the CD, then you should
be
fine. See http://www.michaelstevenstech.com/bios_manufacturer.htm
for
how to do this.

At this point, you should be able to use the Recovery Console from
your
installation CD.

(Do you have an installation CD? Or is it a different type of
"WinXP
CD"?)


WindowsXPert wrote:
1. Boot to Recovery Console.

2 . type the following commands
cd system32 [enter]

ren winlogon.exe winlogon.old
ren msgina.dll msgina.old
ren shell32.dll shell32.old
ren shlwapi.dll shlwapi.old

cd.. [enter]
cd servicepackfiles\i386 [enter]
copy MSGINA.DLL c:\windows\system32
copy SHELL32.DLL c:\windows\system32
copy WINLOGON.EXE c:\windows\system32
copy shlwapi.dll c:\windows\system32

if not there, expand from the cd

3 Type EXIT and hit enter


:

Please help anybody!
My laptop crashed yesterday. and it want open windows.
It is askink for msgina.dll and to notify administrator, asking
for
restart adn this again and again.
Copied the file on a disk from my big computer, but how can I
feed
it in now? Can`t fin also no feature to make a start up copy to
try
this.
Have the original WinXP CD but it doesn`t work either.
Pleas help somebody
Thank you
Ursula

 

[Guest]

Thank you both sooo much, problem solved, lappi running like new
greetings Ursula

You are both too kind to help me out, thanks a lot!!!
I tried the article too, no help. I wrote the ren thing right in the console
and the names are changed. Puter couldn't find the msgina.dll but the others.
then I tried to go in from windows, but without the proper msgina no way. so
I tried to go to D:\ but puter went to D and right back to C:\. Tried every
letter to see, if its there (CD-ROM) but it told me no disk to find there (it
WAS in the player).
How can I find the CD on console?
Thanks again
Ursula

I'm pretty sure that article takes you through a process similar (if not
identical) to the one in my earlier post.

By the way, the command you were having a problem with earlier --is REN
(R-E-N) *not* REM (R-E-M). In a batch file, "REM" means "Remark" and the
command processor ignores everything which follows until the next [ENTER]
character appears. REN (R-E-N) is short for RENAME, which you can type all
the way out, if you wish.

Hope this helps.

Sam French

We overlooked something! See:

"Logon User Interface DLL Msgina.dll failed to load" error message after
you install the MS04-003 security update"
http://support.microsoft.com/kb/836683



Got the thing with the cd.. wrong, did not put the space in .
My Problem now is to get the CD-Rom working to copy.
When I go down it shows the D:\ comes but back to C:\ ...
Thanks if you can help me here out
Ursula




:

on console i get until end of #2 the following command is not
possible.
Now the second time it tells me the rem command is not recognized.
eithrt is the cd..

:

Additionally, Ursula, you need to make sure you boot off the CD.
You
should access your BIOS setup *before* the PC attempts to boot off
your
hard drive, then configure it to boot off the CD, then you should
be
fine. See http://www.michaelstevenstech.com/bios_manufacturer.htm
for
how to do this.

At this point, you should be able to use the Recovery Console from
your
installation CD.

(Do you have an installation CD? Or is it a different type of
"WinXP
CD"?)


WindowsXPert wrote:
1. Boot to Recovery Console.

2 . type the following commands
cd system32 [enter]

ren winlogon.exe winlogon.old
ren msgina.dll msgina.old
ren shell32.dll shell32.old
ren shlwapi.dll shlwapi.old

cd.. [enter]
cd servicepackfiles\i386 [enter]
copy MSGINA.DLL c:\windows\system32
copy SHELL32.DLL c:\windows\system32
copy WINLOGON.EXE c:\windows\system32
copy shlwapi.dll c:\windows\system32

if not there, expand from the cd

3 Type EXIT and hit enter


:

Please help anybody!
My laptop crashed yesterday. and it want open windows.
It is askink for msgina.dll and to notify administrator, asking
for
restart adn this again and again.
Copied the file on a disk from my big computer, but how can I
feed
it in now? Can`t fin also no feature to make a start up copy to
try
this.
Have the original WinXP CD but it doesn`t work either.
Pleas help somebody
Thank you
Ursula

 

[Daave]

Great news!

Thank you both sooo much, problem solved, lappi running like new
greetings Ursula

You are both too kind to help me out, thanks a lot!!!
I tried the article too, no help. I wrote the ren thing right in the
console
and the names are changed. Puter couldn't find the msgina.dll but the
others.
then I tried to go in from windows, but without the proper msgina no
way. so
I tried to go to D:\ but puter went to D and right back to C:\. Tried
every
letter to see, if its there (CD-ROM) but it told me no disk to find
there (it
WAS in the player).
How can I find the CD on console?
Thanks again
Ursula

I'm pretty sure that article takes you through a process similar
(if not
identical) to the one in my earlier post.

By the way, the command you were having a problem with earlier --is
REN
(R-E-N) *not* REM (R-E-M). In a batch file, "REM" means "Remark"
and the
command processor ignores everything which follows until the next
[ENTER]
character appears. REN (R-E-N) is short for RENAME, which you can
type all
the way out, if you wish.

Hope this helps.

Sam French


:

We overlooked something! See:

"Logon User Interface DLL Msgina.dll failed to load" error
message after
you install the MS04-003 security update"
http://support.microsoft.com/kb/836683



message
Got the thing with the cd.. wrong, did not put the space in
.
My Problem now is to get the CD-Rom working to copy.
When I go down it shows the D:\ comes but back to C:\ ...
Thanks if you can help me here out
Ursula




:

on console i get until end of #2 the following command is not
possible.
Now the second time it tells me the rem command is not
recognized.
eithrt is the cd..

:

Additionally, Ursula, you need to make sure you boot off the
CD.
You
should access your BIOS setup *before* the PC attempts to
boot off
your
hard drive, then configure it to boot off the CD, then you
should
be
fine. See
http://www.michaelstevenstech.com/bios_manufacturer.htm
for
how to do this.

At this point, you should be able to use the Recovery
Console from
your
installation CD.

(Do you have an installation CD? Or is it a different type
of
"WinXP
CD"?)


WindowsXPert wrote:
1. Boot to Recovery Console.

2 . type the following commands
cd system32 [enter]

ren winlogon.exe winlogon.old
ren msgina.dll msgina.old
ren shell32.dll shell32.old
ren shlwapi.dll shlwapi.old

cd.. [enter]
cd servicepackfiles\i386 [enter]
copy MSGINA.DLL c:\windows\system32
copy SHELL32.DLL c:\windows\system32
copy WINLOGON.EXE c:\windows\system32
copy shlwapi.dll c:\windows\system32

if not there, expand from the cd

3 Type EXIT and hit enter


:

Please help anybody!
My laptop crashed yesterday. and it want open windows.
It is askink for msgina.dll and to notify administrator,
asking
for
restart adn this again and again.
Copied the file on a disk from my big computer, but how
can I
feed
it in now? Can`t fin also no feature to make a start up
copy to
try
this.
Have the original WinXP CD but it doesn`t work either.
Pleas help somebody
Thank you
Ursula