You might try a repair install as follows:
NOTE, while a repair install should leave your data files intact, if
something goes wrong during the repair install, you may be forced to start
over and do a clean install of XP. If you don't have your data backed up,
you would lose your data should that eventuality occur.
Assuming your system is set to boot from the CD-ROM drive and you have an
actual XP CD as opposed to a recovery CD, boot with the XP
CD in the drive and perform a repair install as outlined below. If the
system isn't set to boot from the CD or you are not sure, you need to enter
the system's BIOS. When you boot the system, the first screen usually has
instructions that if you wish to enter set press a specific key, when you
see that, do so. Then you will have to navigate to the boot sequence, if
the CD-ROM drive is not first line, set it first in the boot sequence. Save
your settings and exit with the XP CD in the drive. The system will reboot.
When the system boots, a few screens into the process you may see a message
instructing you
to hit any key in order to boot from the CD along with a countdown. When
you see this be sure to
hit a key on the keyboard, if you miss this instruction and the system fails
to boot from the CD, it's too
late, you'll need to reboot and try again.
Once you have pressed a key, setup should begin. You will see a reference
asking if you need to load special drivers and another notice that if you
wish to begin the ASR (Automatic Recovery Console) depress F2. Just let
setup run past all of that. It will continue to load files and drivers.
Then it will bring you to a screen. Eventually, you will come to a screen
with the option to (1) setup Windows or (2) Repair Windows Installation
using the Recovery console. ***The selection you want at this screen is
"Setup Windows,"
NOT "Repair Windows Installation.
The first option, to setup Windows is the one you want and requires you to
press enter. When asked, press F8 to accept the end user agreement. Setup
will then search for previous versions of Windows. Upon finding your
version, it will ask if you wish to Repair your current installation or
install fresh. Press R, that will run a repair installation. From there
on, follow the screens.
If you only have a recovery CD, your options are quite limited. You can
either purchase a retail version of XP will allow you to perform the above
among other tools and options it has or you can run your system recovery
routine with the Recovery CD which will likely wipe your drive, deleting all
files but will restore your setup to factory fresh condition.
If that doesn't resolve it, if you have another available partition on your
hard drive, you might try installing XP to that drive and then copying your
data files from the old setup to the new one. If you don't have an
available partition you could use third party software such as Partition
Magic,
www.powerquest.com, to reduce the size of the current partition in
order to create enough free space in which to create a new partition.
If you do this, you will likely receive an access denied message when trying
to access your data files. If this occurs, take ownership of the files as
follows:
Note, file ownership and permissions supersede administrator rights. How
you resolve it depends upon which version of XP you are running.
XP-Home
Unfortunately, XP Home using NTFS is essentially hard wired for "Simple File
Sharing" at system level.
However, you can set XP Home permissions in Safe Mode. Reboot, and start
hitting F8, a menu should eventually appear and one of the
options is Safe Mode. Select it. Note, it will ask for the administrator's
password. This is not your administrator account, rather it is the
machine's administrator account for which users are asked to create a
password during setup.
If you created no such password, when requested, leave blank and press
enter.
Open Explorer, go to Tools and Folder Options, on the view tab, scroll to
the bottom of the list, if it shows "Enable Simple File Sharing" deselect it
and click apply and ok. If it shows nothing or won't let you make a change,
move on to the next step.
Navigate to the files, right click, select properties, go to the Security
tab, click advanced, go to the Owner tab and select the user that was logged
on when you were refused permission to access the files. Click apply and
ok. Close the properties box, reopen it, click add and type in the name of
the user you just enabled. If you wish to set ownership for everything in
the folder, at the bottom of the Owner tab is the following selection:
"Replace owner on subcontainers and objects," select it as well.
Once complete, you should be able to do what you wish with these files when
you log back on as that user.
XP-Pro
If you have XP Pro, temporarily change the limited account to
administrative. First, go to Windows Explorer, go to Tools, select Folder
Options, go to the View tab and be sure "Use Simple File Sharing" is not
selected. If it is, deselect it and click apply and ok.
If you wish everything in a specific folder to be accessible to a user,
right click the folder, select properties, go to the Security tab, click
Advanced, go to the Owner tab,
select the user you wish to have access, at the bottom of the box, you
should see a check box for "Replace owner on subcontainers and objects,"
place a check in the box and click apply and ok.
The user should now be able to perform necessary functions on files in the
folder even as a limited account. If not, make it an admin account again,
right click the folder, select Properties, go to the Security tab and be
sure the user is listed in the user list. If not, click add and type the
user name in the appropriate box, be sure the user has all the necessary
permissions checked in the permission list below the user list, click apply
and ok.
That should do it and allow whatever access you desire for that folder even
in a limited account.
