Cannot start windows after HW upgrade!

R

Ramon

Hi all

I just replaced the mainboard and the RAM and have not altered the software
in any manner however I cannot start windows it keeps restarting and ends up
in the safe mode selection screen. I chose all options to no luck. Also I
attempted chkdsk /r from recovery console and bootcfg /rebuild to no avail.

Can anyone suggest a way how I can get it to work without havin the need to
reinstall everything from scratch?

OS is Windows XP SP2
 
J

Jim Macklin

You have to do a repair install.



| Hi all
|
| I just replaced the mainboard and the RAM and have not
altered the software
| in any manner however I cannot start windows it keeps
restarting and ends up
| in the safe mode selection screen. I chose all options to
no luck. Also I
| attempted chkdsk /r from recovery console and bootcfg
/rebuild to no avail.
|
| Can anyone suggest a way how I can get it to work without
havin the need to
| reinstall everything from scratch?
|
| OS is Windows XP SP2
|
|
 
D

David B.

This is due to the change in the hard drive controller on the motherboard,
only way to get up and running after you have already swapped the
motherboard is a repair install, then reinstall all Windows updates.
 
B

Bob Harris

links about how to do a repair installation of XP:

http://support.microsoft.com/default.aspx?scid=kb;en-us;315341



http://www.webtree.ca/windowsxp/repair_xp.htm



http://www.extremetech.com/print_article/0,3998,a=23979,00.asp



http://www.geekstogo.com/forum/Repair-Windows-XP-t138.html



Note that the new motherboard probably came with new drivers for assorted
on-board hardware (e.g., video, sound, etc). The repair installation of XP
will fix fundamental things that can prevent XP from booting, and will load
generic drivers that probably will be good enough to get to the XP desktop.
But, after you reach the XP desktop level, you will need to install the new
drivers for maximum functionality.



Additionally, if the hard drive controller on the motherboard is RAID, SCSI,
or SATA you may need to hit F6 early during the repair process and install
special drivers for the disk controller. Such drivers must be on a floppy,
not on a CD. If the hard drive is an old-fashioned IDE or ATA, and not part
of a RAID array, then the F6 trick should not be required, since you are
dealing with IDE/ATA type controllers, which have native support under XP.
 
B

Bruce Chambers

Ramon said:
Hi all

I just replaced the mainboard and the RAM and have not altered the software
in any manner however I cannot start windows it keeps restarting and ends up
in the safe mode selection screen. I chose all options to no luck. Also I
attempted chkdsk /r from recovery console and bootcfg /rebuild to no avail.

Can anyone suggest a way how I can get it to work without havin the need to
reinstall everything from scratch?

OS is Windows XP SP2


Normally, and assuming a retail license (many factory-installed OEM
installations are BIOS-locked to a specific chipset and therefore are
*not* transferable to a new motherboard - check yours before starting),
unless the new motherboard is virtually identical (same chipset, same
IDE controllers, same BIOS version, etc.) to the one on which the WinXP
installation was originally performed, you'll need to perform a repair
(a.k.a. in-place upgrade) installation, at the very least:

How to Perform an In-Place Upgrade of Windows XP
http://support.microsoft.com/directory/article.asp?ID=KB;EN-US;Q315341

Changing a Motherboard or Moving a Hard Drive with WinXP Installed
http://www.michaelstevenstech.com/moving_xp.html

The "why" is quite simple, really, and has nothing to do with
licensing issues, per se; it's a purely technical matter, at this point.
You've pulled the proverbial hardware rug out from under the OS. (If
you don't like -- or get -- the rug analogy, think of it as picking up a
Cape Cod style home and then setting it down onto a Ranch style
foundation. It just isn't going to fit.) WinXP, like Win2K before it,
is not nearly as "promiscuous" as Win9x when it comes to accepting any
old hardware configuration you throw at it. On installation it
"tailors" itself to the specific hardware found. This is one of the
reasons that the entire WinNT/2K/XP OS family is so much more stable
than the Win9x group.

As always when undertaking such a significant change, back up any
important data before starting.

This will also probably require re-activation, unless you have a
Volume Licensed version of WinXP Pro installed. If it's been more than
120 days since you last activated that specific Product Key, you'll most
likely be able to activate via the Internet without problem. If it's
been less, you might have to make a 5 minute phone call.


--

Bruce Chambers

Help us help you:



They that can give up essential liberty to obtain a little temporary
safety deserve neither liberty nor safety. ~Benjamin Franklin

Many people would rather die than think; in fact, most do. ~Bertrand Russell

The philosopher has never killed any priests, whereas the priest has
killed a great many philosophers.
~ Denis Diderot
 

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments. After that, you can post your question and our members will help you out.

Ask a Question

Top