Unknown PC fails bootup & TUFFTEST Lite diagnostic boot

[TJ Sackville-West]

Recovered a Pentium 2 PC with 64MB and Maxtor drive. No idea of OS.
Doesn't boot up. Just beeping sound then a second continuous beep
starts as well.

Tried booting up with TUFFTEST disk to cut straight into DOS but same
beeping starts after a few seconds and then the long tone as well.
Nothing on monitor either.

Might try installing another HDD with an OS that works to test
motherboard.

Any advice how to get DOS running. Or get to the point of reloading an
OS from scratch most welcome.

Thanks

TJ

 

[John Turco]

Recovered a Pentium 2 PC with 64MB and Maxtor drive. No idea of OS.
Doesn't boot up. Just beeping sound then a second continuous beep
starts as well.

Hello, TJ:

That's a "beep code," which is crucial when the system video display
can't initialize. It "tells" you what the problem is, according to the
number of beeps.

Tried booting up with TUFFTEST disk to cut straight into DOS but same
beeping starts after a few seconds and then the long tone as well.
Nothing on monitor either.

Might try installing another HDD with an OS that works to test
motherboard.

Won't help, as the computer must POST, even with no drives (of any
kind) installed. The issue is at a lower level, involving any of the
following, key components: CPU, RAM, BIOS, video adapter, or the
mainboard, itself.

Any advice how to get DOS running. Or get to the point of reloading an
OS from scratch most welcome.

Thanks

TJ

If it's a PC of a major brand (IBM, Dell, etc.), try to find its model
number. Next, search Google <http://www.google.com>, and see whether you
can discover the BIOS manufacturer; then, seek out a list of that
company's beep codes.

On the other hand, if it's a home-built machine, remove its case cover
and locate the BIOS chip (mounted on the mainboard). It should have a
sticker on it, with the BIOS maker's name printed there (e.g., Award,
AMI BIOS, etc.).

Good luck!


Cordially,
John Turco <[email protected]>

 

[TE Cheah]

| Just beeping sound then a second continuous beep

clean dimms & agp card's contact points & their slots' pins

www.pcguide.com/ref/mbsys/bios/compBoot-c.html
try to boot from a pci / isa slot display card

http://www4.tomshardware.com/howto/01q3/010725/bios_tuning-02.html

 

[TJ Sackville-West]

Hello, TJ:

That's a "beep code," which is crucial when the system video display
can't initialize. It "tells" you what the problem is, according to the
number of beeps.


Won't help, as the computer must POST, even with no drives (of any
kind) installed. The issue is at a lower level, involving any of the
following, key components: CPU, RAM, BIOS, video adapter, or the
mainboard, itself.


If it's a PC of a major brand (IBM, Dell, etc.), try to find its model
number. Next, search Google <http://www.google.com>, and see whether you
can discover the BIOS manufacturer; then, seek out a list of that
company's beep codes.

On the other hand, if it's a home-built machine, remove its case cover
and locate the BIOS chip (mounted on the mainboard). It should have a
sticker on it, with the BIOS maker's name printed there (e.g., Award,
AMI BIOS, etc.).

Thanks for this advice. All of the above is what I feared, starting
with the BIOS and working through to possible faults on the
motherboard. Sad thruth is the CPU is probably a PII/500, board only
has 64Mb RAM and as I planned to install Suse Linux 9.1 (which is slow
on a 400 Celeron with 192MB RAM) I will sell this board as is for a
few bucks to a hobbyist to repair and buy a new motherboard with AMD
2600 rather than invest more time and money in a limited system.

TJ