networking problem

K

Karoly Vaczko (FM)

Hello,

I'm facing with a new problem now...

Configuration: my hardware and a shell prototype that I created in
component designer (it is actually a cmd.exe componentized, nothing
more). including components: network command shell, network command
shell interface. Then running auto-resolve created an image that was
able to boot.

FBAlog.txt shows the following interesting:

19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\ndisuio.inf -c p -i MS_NDISUIO (ExitCode: 0x8007000d)
19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\netwzc.inf -c s -i MS_WZCSVC (ExitCode: 0x8007000d)
19:48:09 PM - [FBARegQueue: DllRegisterServer]
D:\WINDOWS\System32\activeds.dll (Error: 0x80040154)
19:48:10 PM - [FBARegQueue: DllInstall]
D:\WINDOWS\System32\userenv.dll (Error: 0x80040154)

After booting into the shell, I managed to start netsh, here is the
screen capture:

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

D:\WINDOWS\System32>netsh

WARNING: Could not obtain host information from machine:
[OEM-OGQRQ6TRR00]. Some
commands may not be available.
Class not registered

netsh>interface ip
netsh interface ip>show config
The request is not supported.


netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>show dns
The request is not supported.

netsh interface ip>add address "Local Area Connection" 192.168.2.155
255.255.255
..0

Invalid interface Local Area Connection specified.

netsh interface ip>dump


# ----------------------------------
# Interface IP Configuration
# ----------------------------------
pushd interface ip



popd
# End of interface IP configuration


netsh interface ip>reset d:\resetlog.txt

netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>exit


D:\WINDOWS\System32>net start remoteaccess
The service name is invalid.

More help is available by typing NET HELPMSG 2185.


D:\WINDOWS\System32>



resetlog.txt:

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\1\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpSubnetMaskOpt
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpSubnetMaskOpt

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\3\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDefaultGateway
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpDefaultGateway

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\6\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpNameServer
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\15\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDomain
SYSTEM\CurrentControlSet\Services\TcpIp\Parameters\DhcpDomain

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\44\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\NetBT\Parameters\Interfaces\Tcpip_?\DhcpNameServerList
SYSTEM\CurrentControlSet\Services\NetBT\Adapters\?\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\46\RegLocation
old REG_SZ =
SYSTEM\CurrentControlSet\Services\NetBT\Parameters\DhcpNodeType

added SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\ServiceDll
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DatabasePath
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\ForwardBroadcasts
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\IpEnableRouter
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\NameServer
added
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Winsock\UseDelayedAcceptance
Failed to load network configuration from the registry. (hr=0x8007000d)
<completed>




What do I miss from the configuration so that the ethernet interface
could be initilaized and the computer will be then "pingable"?

Thanks for your help in advance. I apologize for the long post.

Regards,


Karoly
 
K

Karoly Vaczko (FM)

Karoly Vaczko (FM) írta:
Hello,

I'm facing with a new problem now...

Configuration: my hardware and a shell prototype that I created in
component designer (it is actually a cmd.exe componentized, nothing
more). including components: network command shell, network command
shell interface. Then running auto-resolve created an image that was
able to boot.

FBAlog.txt shows the following interesting:

19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\ndisuio.inf -c p -i MS_NDISUIO (ExitCode: 0x8007000d)
19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\netwzc.inf -c s -i MS_WZCSVC (ExitCode: 0x8007000d)
19:48:09 PM - [FBARegQueue: DllRegisterServer]
D:\WINDOWS\System32\activeds.dll (Error: 0x80040154)
19:48:10 PM - [FBARegQueue: DllInstall]
D:\WINDOWS\System32\userenv.dll (Error: 0x80040154)

After booting into the shell, I managed to start netsh, here is the
screen capture:

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

D:\WINDOWS\System32>netsh

WARNING: Could not obtain host information from machine:
[OEM-OGQRQ6TRR00]. Some
commands may not be available.
Class not registered

netsh>interface ip
netsh interface ip>show config
The request is not supported.


netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>show dns
The request is not supported.

netsh interface ip>add address "Local Area Connection" 192.168.2.155
255.255.255
..0

Invalid interface Local Area Connection specified.

netsh interface ip>dump


# ----------------------------------
# Interface IP Configuration
# ----------------------------------
pushd interface ip



popd
# End of interface IP configuration


netsh interface ip>reset d:\resetlog.txt

netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>exit


D:\WINDOWS\System32>net start remoteaccess
The service name is invalid.

More help is available by typing NET HELPMSG 2185.


D:\WINDOWS\System32>



resetlog.txt:

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\1\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpSubnetMaskOpt

SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpSubnetMaskOpt

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\3\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDefaultGateway

SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpDefaultGateway

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\6\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpNameServer

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\15\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDomain
SYSTEM\CurrentControlSet\Services\TcpIp\Parameters\DhcpDomain

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\44\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\NetBT\Parameters\Interfaces\Tcpip_?\DhcpNameServerList

SYSTEM\CurrentControlSet\Services\NetBT\Adapters\?\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\46\RegLocation
old REG_SZ =
SYSTEM\CurrentControlSet\Services\NetBT\Parameters\DhcpNodeType

added SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\ServiceDll
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DatabasePath
added
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\ForwardBroadcasts
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\IpEnableRouter
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\NameServer
added
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Winsock\UseDelayedAcceptance

Failed to load network configuration from the registry. (hr=0x8007000d)
<completed>




What do I miss from the configuration so that the ethernet interface
could be initilaized and the computer will be then "pingable"?

Thanks for your help in advance. I apologize for the long post.

Regards,


Karoly
Click to expand...


Just some addition:

I followed the steps described here:

http://msdn.microsoft.com/library/default.asp?url=/library/en-us/xpehelp/html/xehowNetworking.asp

So, I added IP Router Monitor Library and TCP/IP Utilities. The result
is exactly the same I had before, described above.

I'm disappointed because the first error (ExitCode: 0x8007000d) could be
the key in my opinion, however I couldn't find anything on that except:
"The data is invalid.". It is not too much.

Regards,

Karoly
 
S

Slobodan Brcin \(eMVP\)

Karoly,

Does this help?
http://groups-beta.google.com/group/microsoft.public.windowsxp.embedded/msg/552f346383b56dcb

Regards,
Slobodan

Karoly Vaczko (FM) said:
Hello,

I'm facing with a new problem now...

Configuration: my hardware and a shell prototype that I created in
component designer (it is actually a cmd.exe componentized, nothing
more). including components: network command shell, network command
shell interface. Then running auto-resolve created an image that was
able to boot.

FBAlog.txt shows the following interesting:

19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\ndisuio.inf -c p -i MS_NDISUIO (ExitCode: 0x8007000d)
19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\netwzc.inf -c s -i MS_WZCSVC (ExitCode: 0x8007000d)
19:48:09 PM - [FBARegQueue: DllRegisterServer]
D:\WINDOWS\System32\activeds.dll (Error: 0x80040154)
19:48:10 PM - [FBARegQueue: DllInstall]
D:\WINDOWS\System32\userenv.dll (Error: 0x80040154)

After booting into the shell, I managed to start netsh, here is the
screen capture:

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

D:\WINDOWS\System32>netsh

WARNING: Could not obtain host information from machine:
[OEM-OGQRQ6TRR00]. Some
commands may not be available.
Class not registered

netsh>interface ip
netsh interface ip>show config
The request is not supported.


netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>show dns
The request is not supported.

netsh interface ip>add address "Local Area Connection" 192.168.2.155
255.255.255
.0

Invalid interface Local Area Connection specified.

netsh interface ip>dump


# ----------------------------------
# Interface IP Configuration
# ----------------------------------
pushd interface ip



popd
# End of interface IP configuration


netsh interface ip>reset d:\resetlog.txt

netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>exit


D:\WINDOWS\System32>net start remoteaccess
The service name is invalid.

More help is available by typing NET HELPMSG 2185.


D:\WINDOWS\System32>



resetlog.txt:

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\1\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpSubnetMaskOpt
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpSubnetMaskOpt

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\3\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDefaultGateway
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpDefaultGateway

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\6\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpNameServer
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\15\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDomain
SYSTEM\CurrentControlSet\Services\TcpIp\Parameters\DhcpDomain

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\44\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\NetBT\Parameters\Interfaces\Tcpip_?\DhcpNameServerList
SYSTEM\CurrentControlSet\Services\NetBT\Adapters\?\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\46\RegLocation
old REG_SZ =
SYSTEM\CurrentControlSet\Services\NetBT\Parameters\DhcpNodeType

added SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\ServiceDll
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DatabasePath
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\ForwardBroadcasts
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\IpEnableRouter
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\NameServer
added
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Winsock\UseDelayedAcceptance
Failed to load network configuration from the registry. (hr=0x8007000d)
<completed>




What do I miss from the configuration so that the ethernet interface
could be initilaized and the computer will be then "pingable"?

Thanks for your help in advance. I apologize for the long post.

Regards,


Karoly
Click to expand...
 
K

KM

Karoly,

Do you have "IP Router Monitor Library" component included?

Also, make sure the network driver gets instaled properly. If not, please show us the setupapi.log.

--
Regards,
KM, BSquare Corp.

Hello,

I'm facing with a new problem now...

Configuration: my hardware and a shell prototype that I created in
component designer (it is actually a cmd.exe componentized, nothing
more). including components: network command shell, network command
shell interface. Then running auto-resolve created an image that was
able to boot.

FBAlog.txt shows the following interesting:

19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\ndisuio.inf -c p -i MS_NDISUIO (ExitCode: 0x8007000d)
19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\netwzc.inf -c s -i MS_WZCSVC (ExitCode: 0x8007000d)
19:48:09 PM - [FBARegQueue: DllRegisterServer]
D:\WINDOWS\System32\activeds.dll (Error: 0x80040154)
19:48:10 PM - [FBARegQueue: DllInstall]
D:\WINDOWS\System32\userenv.dll (Error: 0x80040154)

After booting into the shell, I managed to start netsh, here is the
screen capture:

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

D:\WINDOWS\System32>netsh

WARNING: Could not obtain host information from machine:
[OEM-OGQRQ6TRR00]. Some
commands may not be available.
Class not registered

netsh>interface ip
netsh interface ip>show config
The request is not supported.


netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>show dns
The request is not supported.

netsh interface ip>add address "Local Area Connection" 192.168.2.155
255.255.255
.0

Invalid interface Local Area Connection specified.

netsh interface ip>dump


# ----------------------------------
# Interface IP Configuration
# ----------------------------------
pushd interface ip



popd
# End of interface IP configuration


netsh interface ip>reset d:\resetlog.txt

netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>exit


D:\WINDOWS\System32>net start remoteaccess
The service name is invalid.

More help is available by typing NET HELPMSG 2185.


D:\WINDOWS\System32>



resetlog.txt:

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\1\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpSubnetMaskOpt
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpSubnetMaskOpt

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\3\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDefaultGateway
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpDefaultGateway

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\6\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpNameServer
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\15\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDomain
SYSTEM\CurrentControlSet\Services\TcpIp\Parameters\DhcpDomain

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\44\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\NetBT\Parameters\Interfaces\Tcpip_?\DhcpNameServerList
SYSTEM\CurrentControlSet\Services\NetBT\Adapters\?\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\46\RegLocation
old REG_SZ =
SYSTEM\CurrentControlSet\Services\NetBT\Parameters\DhcpNodeType

added SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\ServiceDll
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DatabasePath
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\ForwardBroadcasts
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\IpEnableRouter
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\NameServer
added
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Winsock\UseDelayedAcceptance
Failed to load network configuration from the registry. (hr=0x8007000d)
<completed>




What do I miss from the configuration so that the ethernet interface
could be initilaized and the computer will be then "pingable"?

Thanks for your help in advance. I apologize for the long post.

Regards,


Karoly
Click to expand...
 
K

KM

I see I am too late.

Anyway, we better know if the network driver is installed.

--
Regards,
KM, BSquare Corp.

Karoly,

Do you have "IP Router Monitor Library" component included?

Also, make sure the network driver gets instaled properly. If not, please show us the setupapi.log.

--
Regards,
KM, BSquare Corp.

Hello,

I'm facing with a new problem now...

Configuration: my hardware and a shell prototype that I created in
component designer (it is actually a cmd.exe componentized, nothing
more). including components: network command shell, network command
shell interface. Then running auto-resolve created an image that was
able to boot.

FBAlog.txt shows the following interesting:

19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\ndisuio.inf -c p -i MS_NDISUIO (ExitCode: 0x8007000d)
19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\netwzc.inf -c s -i MS_WZCSVC (ExitCode: 0x8007000d)
19:48:09 PM - [FBARegQueue: DllRegisterServer]
D:\WINDOWS\System32\activeds.dll (Error: 0x80040154)
19:48:10 PM - [FBARegQueue: DllInstall]
D:\WINDOWS\System32\userenv.dll (Error: 0x80040154)

After booting into the shell, I managed to start netsh, here is the
screen capture:

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

D:\WINDOWS\System32>netsh

WARNING: Could not obtain host information from machine:
[OEM-OGQRQ6TRR00]. Some
commands may not be available.
Class not registered

netsh>interface ip
netsh interface ip>show config
The request is not supported.


netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>show dns
The request is not supported.

netsh interface ip>add address "Local Area Connection" 192.168.2.155
255.255.255
.0

Invalid interface Local Area Connection specified.

netsh interface ip>dump


# ----------------------------------
# Interface IP Configuration
# ----------------------------------
pushd interface ip



popd
# End of interface IP configuration


netsh interface ip>reset d:\resetlog.txt

netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>exit


D:\WINDOWS\System32>net start remoteaccess
The service name is invalid.

More help is available by typing NET HELPMSG 2185.


D:\WINDOWS\System32>



resetlog.txt:

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\1\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpSubnetMaskOpt
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpSubnetMaskOpt

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\3\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDefaultGateway
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpDefaultGateway

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\6\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpNameServer
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\15\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDomain
SYSTEM\CurrentControlSet\Services\TcpIp\Parameters\DhcpDomain

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\44\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\NetBT\Parameters\Interfaces\Tcpip_?\DhcpNameServerList
SYSTEM\CurrentControlSet\Services\NetBT\Adapters\?\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\46\RegLocation
old REG_SZ =
SYSTEM\CurrentControlSet\Services\NetBT\Parameters\DhcpNodeType

added SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\ServiceDll
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DatabasePath
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\ForwardBroadcasts
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\IpEnableRouter
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\NameServer
added
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Winsock\UseDelayedAcceptance
Failed to load network configuration from the registry. (hr=0x8007000d)
<completed>




What do I miss from the configuration so that the ethernet interface
could be initilaized and the computer will be then "pingable"?

Thanks for your help in advance. I apologize for the long post.

Regards,


Karoly
Click to expand...
Click to expand...
 
K

Karoly Vaczko (FM)

Slobodan,

It did help. Thanks a lot. The problem was that I installed netsh and
netsh extensions hoping that it will depend on the core networking
components. Well, it didn't. I put together a howto about that, it was
tested under XPe SP1. Here it goes:



Static IP address configuration in Windows XPe environment HOWTO


To be able to be pingable with one ethernet card in your target machine,
you have to add the followings in TD:

-driver of your ethernet card
-Software : System : Networking & Communications; Basic TCP/IP
Networking macro
-Software : System : Networking & Communications : Applications;
Network Command Shell
-Software : System : Networking & Communications : Applications; Network
Command Shell Interface Context
-Software : System : Networking & Communications : Applications; IP
Router Monitor Library
-Software : System : Networking & Communications : Applications; TCP/IP
Utilities
-Software : System : System Services : Base; CMD - Windows Command Processor


Let's make a dependency check, FBA your image and boot. Run CMD.exe.

Enter ipconfig and press enter

For the two possible scenarios here are the screen outputs of ipconfig:

1) your network card is NOT installed properly

D:\WINDOWS\system32>ipconfig

Windows IP Configuration


D:\WINDOWS\system32>

2) your network adapter IS installed properly (it will be smilar, but
not exactly the same ID {C675....blabla} - it is OK like that)

D:\WINDOWS\system32>ipconfig

Windows IP Configuration


Ethernet adapter {C6757181-2472-44F4-BB41-926220B75EDA}:

Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 0.0.0.0
Subnet Mask . . . . . . . . . . . : 0.0.0.0
Default Gateway . . . . . . . . . :

D:\WINDOWS\system32>


The above section tells you that you have a loaded network driver. If
there is no section like Ethernet adapter or so in the ipconfig output,
it is most probably a wrongly installed network driver that you should
resolve first.

Now, you should be patient here. If you do the following steps quickly
(as I did for the first three-four times) you might receive errors. Wait
about one minute before continue. The reason is most probably that XPe
comes with DHCP client and it is trying to get an IP address from a DHCP
server - the timeout should be about one minute.

In the meantime, if you do ipconfig for a couple of times, the output
should be altered once and becomes similar to this:

D:\WINDOWS\system32>ipconfig

Windows IP Configuration


Ethernet adapter {C6757181-2472-44F4-BB41-926220B75EDA}:

Connection-specific DNS Suffix . :
Autoconfiguration IP Address. . . : 169.254.73.29
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :

D:\WINDOWS\system32>

You should notice here that the IP address and the subnet mask has been
changed by XPe, and also the _name_ of IP address line has changed from
'IP Address' to 'Autoconfiguration IP Address'. Once you notice that
there is an Autoconfiguration IP Address line in your configuration, you
must continue with this command:

rundll32 netshell.dll HrRenameConnection

The output of this command should be the prompt. I was not able to get
any other command line outputs (except when I made a typo in the
rundll32 or netshell.dll). If you make a typo in HrRenameConnection, you
are going to receive a messagebox on the GUI (!!!) that something is
going wrong.

The result of the above command should be seen immediately with ipconfig
again, it produces something like this:

D:\WINDOWS\system32>ipconfig

Windows IP Configuration


Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Autoconfiguration IP Address. . . : 169.254.73.29
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :

D:\WINDOWS\system32>


Notice that you finally have a name of your connection, so that you are
now able to manage your ethernet card in netsh. If you are using other
language than English, "Local Area Connection" will appear in your local
language (for instance, my connection is named as "Helyi kapcsolat").

To set up a static IP address and mask, do this:

netsh interface ip set address name="Local Area Connection"
source=static addr=192.168.2.102 mask=255.255.255.0

To set up a gateway:

netsh interface ip set address name="Local Area Connection"
gateway=192.168.2.1 gwmetric=0

To set up a primary DNS:

netsh interface ip set dns name="Local Area Connection" source=static
addr=145.236.227.108 register=PRIMARY

To set up a secondary DNS:

netsh interface ip add dns name="Local Area Connection"
addr=145.236.88.66 index=2


TRICK: if you don't want to take your time with the syntax of netsh, set
up all ip address and related parameters of the target machine on your
_development_ machine through the friendly XP user interface. Then go to
cmd and enter the following line:

netsh interface ip dump >c:\ipparams.txt

This creates a file at c:\ named ipparams.txt that will contain the
network configuration that you would like to deploy on the target machine.

To implement this file on your target machine, simply copy the file
there, and do this command at the command line:

netsh <c:\ipparams.txt

The ipparams.txt file can be edited with a simple text editor, so
replacing a DNS or changing the IP address would not be a big deal then.

After all, do an ipconfig /all command and it will result this:

D:\WINDOWS\system32>ipconfig /all


Windows IP Configuration

Host Name . . . . . . . . . . . . : OEM-SREVWEVPFUT
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit
Ethernet
Physical Address. . . . . . . . . : 00-11-85-DB-ED-8E
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.2.102
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.2.1
DNS Servers . . . . . . . . . . . : 145.236.227.108
145.236.88.66

D:\WINDOWS\system32>



IMPORTANT! If you change from DHCP to static IP addressing or vica
versa, the 'netsh interface ip set address' command may take a while (I
measured 20 seconds once!). DON'T PANIC!



I hope that the above could help to easily set up your static IP in XPe
(also I hope it works for others as well not just me only! :) ).
Comments/corrections/updates are welcome.

Thank you guys again for the support.

Regards,


Karoly

Slobodan Brcin (eMVP) írta:
Karoly,

Does this help?
http://groups-beta.google.com/group/microsoft.public.windowsxp.embedded/msg/552f346383b56dcb

Regards,
Slobodan

Karoly Vaczko (FM) said:
Hello,

I'm facing with a new problem now...

Configuration: my hardware and a shell prototype that I created in
component designer (it is actually a cmd.exe componentized, nothing
more). including components: network command shell, network command
shell interface. Then running auto-resolve created an image that was
able to boot.

FBAlog.txt shows the following interesting:

19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\ndisuio.inf -c p -i MS_NDISUIO (ExitCode: 0x8007000d)
19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\netwzc.inf -c s -i MS_WZCSVC (ExitCode: 0x8007000d)
19:48:09 PM - [FBARegQueue: DllRegisterServer]
D:\WINDOWS\System32\activeds.dll (Error: 0x80040154)
19:48:10 PM - [FBARegQueue: DllInstall]
D:\WINDOWS\System32\userenv.dll (Error: 0x80040154)

After booting into the shell, I managed to start netsh, here is the
screen capture:

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

D:\WINDOWS\System32>netsh

WARNING: Could not obtain host information from machine:
[OEM-OGQRQ6TRR00]. Some
commands may not be available.
Class not registered

netsh>interface ip
netsh interface ip>show config
The request is not supported.


netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>show dns
The request is not supported.

netsh interface ip>add address "Local Area Connection" 192.168.2.155
255.255.255
.0

Invalid interface Local Area Connection specified.

netsh interface ip>dump


# ----------------------------------
# Interface IP Configuration
# ----------------------------------
pushd interface ip



popd
# End of interface IP configuration


netsh interface ip>reset d:\resetlog.txt

netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>exit


D:\WINDOWS\System32>net start remoteaccess
The service name is invalid.

More help is available by typing NET HELPMSG 2185.


D:\WINDOWS\System32>



resetlog.txt:

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\1\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpSubnetMaskOpt
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpSubnetMaskOpt

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\3\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDefaultGateway
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpDefaultGateway

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\6\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpNameServer
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\15\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDomain
SYSTEM\CurrentControlSet\Services\TcpIp\Parameters\DhcpDomain

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\44\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\NetBT\Parameters\Interfaces\Tcpip_?\DhcpNameServerList
SYSTEM\CurrentControlSet\Services\NetBT\Adapters\?\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\46\RegLocation
old REG_SZ =
SYSTEM\CurrentControlSet\Services\NetBT\Parameters\DhcpNodeType

added SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\ServiceDll
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DatabasePath
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\ForwardBroadcasts
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\IpEnableRouter
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\NameServer
added
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Winsock\UseDelayedAcceptance
Failed to load network configuration from the registry. (hr=0x8007000d)
<completed>




What do I miss from the configuration so that the ethernet interface
could be initilaized and the computer will be then "pingable"?

Thanks for your help in advance. I apologize for the long post.

Regards,


Karoly
Click to expand...
Click to expand...
 
S

Slobodan Brcin \(eMVP\)

Karoly,

Thanks for info, I'm sure that it will help someone in the future :)

Regards,
Slobodan


Karoly Vaczko (FM) said:
Slobodan,

It did help. Thanks a lot. The problem was that I installed netsh and
netsh extensions hoping that it will depend on the core networking
components. Well, it didn't. I put together a howto about that, it was
tested under XPe SP1. Here it goes:



Static IP address configuration in Windows XPe environment HOWTO


To be able to be pingable with one ethernet card in your target machine,
you have to add the followings in TD:

-driver of your ethernet card
-Software : System : Networking & Communications; Basic TCP/IP
Networking macro
-Software : System : Networking & Communications : Applications;
Network Command Shell
-Software : System : Networking & Communications : Applications; Network
Command Shell Interface Context
-Software : System : Networking & Communications : Applications; IP
Router Monitor Library
-Software : System : Networking & Communications : Applications; TCP/IP
Utilities
-Software : System : System Services : Base; CMD - Windows Command Processor


Let's make a dependency check, FBA your image and boot. Run CMD.exe.

Enter ipconfig and press enter

For the two possible scenarios here are the screen outputs of ipconfig:

1) your network card is NOT installed properly

D:\WINDOWS\system32>ipconfig

Windows IP Configuration


D:\WINDOWS\system32>

2) your network adapter IS installed properly (it will be smilar, but
not exactly the same ID {C675....blabla} - it is OK like that)

D:\WINDOWS\system32>ipconfig

Windows IP Configuration


Ethernet adapter {C6757181-2472-44F4-BB41-926220B75EDA}:

Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 0.0.0.0
Subnet Mask . . . . . . . . . . . : 0.0.0.0
Default Gateway . . . . . . . . . :

D:\WINDOWS\system32>


The above section tells you that you have a loaded network driver. If
there is no section like Ethernet adapter or so in the ipconfig output,
it is most probably a wrongly installed network driver that you should
resolve first.

Now, you should be patient here. If you do the following steps quickly
(as I did for the first three-four times) you might receive errors. Wait
about one minute before continue. The reason is most probably that XPe
comes with DHCP client and it is trying to get an IP address from a DHCP
server - the timeout should be about one minute.

In the meantime, if you do ipconfig for a couple of times, the output
should be altered once and becomes similar to this:

D:\WINDOWS\system32>ipconfig

Windows IP Configuration


Ethernet adapter {C6757181-2472-44F4-BB41-926220B75EDA}:

Connection-specific DNS Suffix . :
Autoconfiguration IP Address. . . : 169.254.73.29
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :

D:\WINDOWS\system32>

You should notice here that the IP address and the subnet mask has been
changed by XPe, and also the _name_ of IP address line has changed from
'IP Address' to 'Autoconfiguration IP Address'. Once you notice that
there is an Autoconfiguration IP Address line in your configuration, you
must continue with this command:

rundll32 netshell.dll HrRenameConnection

The output of this command should be the prompt. I was not able to get
any other command line outputs (except when I made a typo in the
rundll32 or netshell.dll). If you make a typo in HrRenameConnection, you
are going to receive a messagebox on the GUI (!!!) that something is
going wrong.

The result of the above command should be seen immediately with ipconfig
again, it produces something like this:

D:\WINDOWS\system32>ipconfig

Windows IP Configuration


Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Autoconfiguration IP Address. . . : 169.254.73.29
Subnet Mask . . . . . . . . . . . : 255.255.0.0
Default Gateway . . . . . . . . . :

D:\WINDOWS\system32>


Notice that you finally have a name of your connection, so that you are
now able to manage your ethernet card in netsh. If you are using other
language than English, "Local Area Connection" will appear in your local
language (for instance, my connection is named as "Helyi kapcsolat").

To set up a static IP address and mask, do this:

netsh interface ip set address name="Local Area Connection"
source=static addr=192.168.2.102 mask=255.255.255.0

To set up a gateway:

netsh interface ip set address name="Local Area Connection"
gateway=192.168.2.1 gwmetric=0

To set up a primary DNS:

netsh interface ip set dns name="Local Area Connection" source=static
addr=145.236.227.108 register=PRIMARY

To set up a secondary DNS:

netsh interface ip add dns name="Local Area Connection"
addr=145.236.88.66 index=2


TRICK: if you don't want to take your time with the syntax of netsh, set
up all ip address and related parameters of the target machine on your
_development_ machine through the friendly XP user interface. Then go to
cmd and enter the following line:

netsh interface ip dump >c:\ipparams.txt

This creates a file at c:\ named ipparams.txt that will contain the
network configuration that you would like to deploy on the target machine.

To implement this file on your target machine, simply copy the file
there, and do this command at the command line:

netsh <c:\ipparams.txt

The ipparams.txt file can be edited with a simple text editor, so
replacing a DNS or changing the IP address would not be a big deal then.

After all, do an ipconfig /all command and it will result this:

D:\WINDOWS\system32>ipconfig /all


Windows IP Configuration

Host Name . . . . . . . . . . . . : OEM-SREVWEVPFUT
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Unknown
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No

Ethernet adapter Local Area Connection:

Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit
Ethernet
Physical Address. . . . . . . . . : 00-11-85-DB-ED-8E
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.2.102
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.2.1
DNS Servers . . . . . . . . . . . : 145.236.227.108
145.236.88.66

D:\WINDOWS\system32>



IMPORTANT! If you change from DHCP to static IP addressing or vica
versa, the 'netsh interface ip set address' command may take a while (I
measured 20 seconds once!). DON'T PANIC!



I hope that the above could help to easily set up your static IP in XPe
(also I hope it works for others as well not just me only! :) ).
Comments/corrections/updates are welcome.

Thank you guys again for the support.

Regards,


Karoly

Slobodan Brcin (eMVP) írta:
Karoly,

Does this help?
http://groups-beta.google.com/group/microsoft.public.windowsxp.embedded/msg/552f346383b56dcb

Regards,
Slobodan

Karoly Vaczko (FM) said:
Hello,

I'm facing with a new problem now...

Configuration: my hardware and a shell prototype that I created in
component designer (it is actually a cmd.exe componentized, nothing
more). including components: network command shell, network command
shell interface. Then running auto-resolve created an image that was
able to boot.

FBAlog.txt shows the following interesting:

19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\ndisuio.inf -c p -i MS_NDISUIO (ExitCode: 0x8007000d)
19:47:53 PM - [FBALaunch] D:\WINDOWS\system32\snetcfg.exe -l
D:\WINDOWS\inf\netwzc.inf -c s -i MS_WZCSVC (ExitCode: 0x8007000d)
19:48:09 PM - [FBARegQueue: DllRegisterServer]
D:\WINDOWS\System32\activeds.dll (Error: 0x80040154)
19:48:10 PM - [FBARegQueue: DllInstall]
D:\WINDOWS\System32\userenv.dll (Error: 0x80040154)

After booting into the shell, I managed to start netsh, here is the
screen capture:

Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.

D:\WINDOWS\System32>netsh

WARNING: Could not obtain host information from machine:
[OEM-OGQRQ6TRR00]. Some
commands may not be available.
Class not registered

netsh>interface ip
netsh interface ip>show config
The request is not supported.


netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>show dns
The request is not supported.

netsh interface ip>add address "Local Area Connection" 192.168.2.155
255.255.255
.0

Invalid interface Local Area Connection specified.

netsh interface ip>dump


# ----------------------------------
# Interface IP Configuration
# ----------------------------------
pushd interface ip



popd
# End of interface IP configuration


netsh interface ip>reset d:\resetlog.txt

netsh interface ip>show ipaddress

The Routing and Remote Access Service is not currently running on the
local mach
ine.
Please use 'net start remoteaccess' on the machine to start the service.

netsh interface ip>exit


D:\WINDOWS\System32>net start remoteaccess
The service name is invalid.

More help is available by typing NET HELPMSG 2185.


D:\WINDOWS\System32>



resetlog.txt:

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\1\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpSubnetMaskOpt
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpSubnetMaskOpt

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\3\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDefaultGateway
SYSTEM\CurrentControlSet\Services\?\Parameters\Tcpip\DhcpDefaultGateway

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\6\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpNameServer
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\15\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Interfaces\?\DhcpDomain
SYSTEM\CurrentControlSet\Services\TcpIp\Parameters\DhcpDomain

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\44\RegLocation
old REG_MULTI_SZ =

SYSTEM\CurrentControlSet\Services\NetBT\Parameters\Interfaces\Tcpip_?\DhcpNameServerList
SYSTEM\CurrentControlSet\Services\NetBT\Adapters\?\DhcpNameServer

reset
SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\Options\46\RegLocation
old REG_SZ =
SYSTEM\CurrentControlSet\Services\NetBT\Parameters\DhcpNodeType

added SYSTEM\CurrentControlSet\Services\Dhcp\Parameters\ServiceDll
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DatabasePath
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\ForwardBroadcasts
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\IpEnableRouter
added SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\NameServer
added
SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\Winsock\UseDelayedAcceptance
Failed to load network configuration from the registry. (hr=0x8007000d)
<completed>




What do I miss from the configuration so that the ethernet interface
could be initilaized and the computer will be then "pingable"?

Thanks for your help in advance. I apologize for the long post.

Regards,


Karoly
Click to expand...
Click to expand...
Click to expand...
 
K

Karoly Vaczko (FM)

Hello,

My network saga continues... After successfully having static IP address
(thanks again, Slobodan), I wanted to implement filesharing. Therefore I
added to the configuration the Software : System : Networking &
Communications; TCP/IP Networking with File Sharing and Client For MS
Networks macro and Software : System : Networking & Communications :
Applications; Net.exe Utility.

Everything works fine, except that once the computer starts, 'net
statistics' shows only Workstation service, then I have to wait about
two minutes until the Server service starts. After that 'net statistics'
shows both Server and Workstation services. Of course, until I don't
have the Server service, I'm not able to share a folder on XPe with 'net
share'.

I checked these threads of the NG about server service:

http://groups.google.co.hu/groups?h...Bj%24pEHA.3848%40TK2MSFTNGP14.phx.gbl&rnum=24
http://groups.google.co.hu/groups?h...6160831.14d4e6ae%40posting.google.com&rnum=63
http://groups.google.co.hu/groups?h...CGLe2DHA.1744%40TK2MSFTNGP12.phx.gbl&rnum=105

My XPe SP1 eval installs correctly "Credential Management User
Interface" component.

Is there anything that I can do in order to speed up Server service
start? Or am I doing something wrong?

Regards,


Karoly
 
K

KM

Karoly,

Beside the fact that it is a bit slow what is the problem that you have to wait until the Server service is up?

If you use "net share" from a batch, you can call your own exe just before that and in that process you can create a code to wait
until the Server service is up and running (QueryServiceStatus[Ex]). Or you can use sc.exe utility to query for the service status
from the batch.

Another approach could be taken if you set WorkStation dependency on the Server service. Never tried that, though.

With regards to the slow Server service boot, you can check Event Log to see if any error is reported. Also, if you use DHCP switch
to static IP for testing purposes at least.
 
K

Karoly Vaczko (FM)

KM írta:
Karoly,

Beside the fact that it is a bit slow what is the problem that you have to wait until the Server service is up?

If you use "net share" from a batch, you can call your own exe just before that and in that process you can create a code to wait
until the Server service is up and running (QueryServiceStatus[Ex]). Or you can use sc.exe utility to query for the service status
from the batch.

Another approach could be taken if you set WorkStation dependency on the Server service. Never tried that, though.

With regards to the slow Server service boot, you can check Event Log to see if any error is reported. Also, if you use DHCP switch
to static IP for testing purposes at least.
Click to expand...

Konstantin,

It is not crucial that the 'net share' should work from the first
second. I was just wondering if I made something wrong, and that's why
the Server service doesn't start immediately.

Anyway thank for the info about querying the status of a service.

Regards,


Karoly
 

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments. After that, you can post your question and our members will help you out.

Ask a Question

Similar Threads

Unable to access internet or ping from machine 1
FBWF and Registry Filter (Changing IP Address) 11
Windows XP DHCP Client Option 26 (MTU) 0
tcp/ip driver is invalid 2
FBWF and RegFilter not Persisting Registry Change across reboots 5
Possible solution for DHCP (ip address) and SP2 4
Networking process causes continuous hard drive activity 2
Continuos hard drive activity - here's my HD writes please help 3

Top