D
Dave Patrick
To do a clean install, either boot the Windows 2000 install CD-Rom or setup
disks. The set of four install disks can be created from your Windows 2000
CD-Rom; change to the \bootdisk directory on the CD-Rom and execute
makeboot.exe (from dos) or makebt32.exe (from 32 bit) and follow the
prompts.
You didn't mention the drive controller (possibly SCSI, or ultra DMA, or
ATA100, or raid, or serial ATA), but you may need to boot the Windows 2000
setup disks or CD-Rom and *F6* very early and very important (at setup is
inspecting your system) in the setup to prevent drive controller detection,
and select S to specify additional drivers. Then later you'll be prompted to
insert the manufacturer supplied Windows 2000 driver for your drive's
controller in drive "A"
If you wait and then S to specify additional drivers, then it may be too
late as Windows 2000 Setup at this point may have already assigned the
resources your drive's controller is wanting to use.
When you get to the point, delete the existing NTFS and or other partitions
found. After you delete the partition(s) abort the install, then again
restart the pc booting the CD-Rom or setup disks to avoid unexpected drive
letter assignments with your new install.
Be sure to apply these to your new install before connecting to any network.
http://download.microsoft.com/download/E/6/A/E6A04295-D2A8-40D0-A0C5-241BFECD095E/W2KSP4_EN.EXE
http://www.microsoft.com/technet/security/bulletin/MS03-043.mspx
http://www.microsoft.com/technet/security/bulletin/MS03-049.mspx
--
Regards,
Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft Certified Professional
Microsoft MVP [Windows]
http://www.microsoft.com/protect
:
|I have a Linux box that I am attempting to wipe clean and install W2K
| server. I have cleared the partitions but get the 'inaccessible boot
| device' blue screen during the W2K server installation (from USB bootable
| CD). I've attempted to clear the HDs and get them to 'factory new' state
| but everything I've tried has me back at the 'inaccessible boot device'
blue
| screen during W2K installation. The only thing I can recall not getting
to
| work was changing sector size to 1024.
|
| Used the command 'dd if=/dev.zero of=/dev/hda bs=512 count=1' which is
| supposed to clear the HD to like new state.
|
| Any help is appreciated.
|
| Kevin
|
|
disks. The set of four install disks can be created from your Windows 2000
CD-Rom; change to the \bootdisk directory on the CD-Rom and execute
makeboot.exe (from dos) or makebt32.exe (from 32 bit) and follow the
prompts.
You didn't mention the drive controller (possibly SCSI, or ultra DMA, or
ATA100, or raid, or serial ATA), but you may need to boot the Windows 2000
setup disks or CD-Rom and *F6* very early and very important (at setup is
inspecting your system) in the setup to prevent drive controller detection,
and select S to specify additional drivers. Then later you'll be prompted to
insert the manufacturer supplied Windows 2000 driver for your drive's
controller in drive "A"
If you wait and then S to specify additional drivers, then it may be too
late as Windows 2000 Setup at this point may have already assigned the
resources your drive's controller is wanting to use.
When you get to the point, delete the existing NTFS and or other partitions
found. After you delete the partition(s) abort the install, then again
restart the pc booting the CD-Rom or setup disks to avoid unexpected drive
letter assignments with your new install.
Be sure to apply these to your new install before connecting to any network.
http://download.microsoft.com/download/E/6/A/E6A04295-D2A8-40D0-A0C5-241BFECD095E/W2KSP4_EN.EXE
http://www.microsoft.com/technet/security/bulletin/MS03-043.mspx
http://www.microsoft.com/technet/security/bulletin/MS03-049.mspx
--
Regards,
Dave Patrick ....Please no email replies - reply in newsgroup.
Microsoft Certified Professional
Microsoft MVP [Windows]
http://www.microsoft.com/protect
:
|I have a Linux box that I am attempting to wipe clean and install W2K
| server. I have cleared the partitions but get the 'inaccessible boot
| device' blue screen during the W2K server installation (from USB bootable
| CD). I've attempted to clear the HDs and get them to 'factory new' state
| but everything I've tried has me back at the 'inaccessible boot device'
blue
| screen during W2K installation. The only thing I can recall not getting
to
| work was changing sector size to 1024.
|
| Used the command 'dd if=/dev.zero of=/dev/hda bs=512 count=1' which is
| supposed to clear the HD to like new state.
|
| Any help is appreciated.
|
| Kevin
|
|