Error from SmartHeap Library

[senn]

Can somebody explain me what´s a SmartHeap Library.
This is the name of the error-form that's poping up,
when I try to run a program om my VistaPremium
machine.
The error that´s written:
Mem_Bad_Pointer
SmartHeap error handler recursively re-entered.
What kind of problem could that be.
--senn

 

[Malke]

Can somebody explain me what´s a SmartHeap Library.
This is the name of the error-form that's poping up,
when I try to run a program om my VistaPremium
machine.
The error that´s written:
Mem_Bad_Pointer
SmartHeap error handler recursively re-entered.
What kind of problem could that be.
--senn

What program?

Malke

 

[senn]

What program?

Malke
--
MS-MVP
Elephant Boy Computers
www.elephantboycomputers.com
Don't Panic!

Hi,
Looks forward having your comments to what you se below.
Though, I do not expect these few informations will help you.
But, if you can narrow the problem belonging to a category,
I might at least have a ground to start off for more servey.
Thank you.
--senn

This old version of Autocad is no longer supported.
Still I found some files on their download site,
none of which cancel the issue.

Produkt
AutoCAD Application

Problem
ProgramCompatibility

Dato
12-02-2008 21:17

Status
Not reportet.
Problemsignatur
Problemhændelsesnavn: PCA2
Problemsignatur 01: acad.exe
Problemsignatur 02: 20.0.0.1
Problemsignatur 03: AutoCAD Application
Problemsignatur 04: AutoCAD
Problemsignatur 05: Autodesk, Inc.
Problemsignatur 06: 200
Problemsignatur 07: -1
OS-version: 6.0.6000.2.0.0.768.3

 

[Malke]

senn wrote:

Looks forward having your comments to what you se below.
Though, I do not expect these few informations will help you.
But, if you can narrow the problem belonging to a category,
I might at least have a ground to start off for more servey.
Thank you.
--senn

This old version of Autocad is no longer supported.
Still I found some files on their download site,
none of which cancel the issue.

(snippage)

The information you already have says it all: the version of AutoCAD you are
trying to run is not compatible with Vista. You can possibly run it in
compatibility mode (look in Vista's Help & Support for instructions) but if
that doesn't work, you need to either get a new version of AutoCAD that
supports Vista OR use Virtual computing (VMware, Virtual PC) and install a
guest operating system that will run your old AutoCAD program.

Downloading various files from the old program will not help.

Malke

 

[senn]

senn wrote:



(snippage)

The information you already have says it all: the version of AutoCAD you
are
trying to run is not compatible with Vista. You can possibly run it in
compatibility mode (look in Vista's Help & Support for instructions) but
if
that doesn't work, you need to either get a new version of AutoCAD that
supports Vista OR use Virtual computing (VMware, Virtual PC) and install a
guest operating system that will run your old AutoCAD program.

Downloading various files from the old program will not help.

Malke
--
MS-MVP
Elephant Boy Computers
www.elephantboycomputers.com
Don't Panic!

I've tryed out the all compatibility modes, including
all the different decoupling settings on the compatibility
page. In fact, the program usely run on my work station,
which is a XP machine. It raned fine here in more than
8 years. Until a couple of weeks ago I re-installed
XP after upgraded to a bigger HD, and raised memory
from 256MB to 1.79GB. Here, I now get an error when
unloading autocad. If I re-install XP with only SP1 and
256MB memory, acad will run trouble fri again.
I tryed VPC 2007 on my XP machine, but it runs too
far slowly. That much slowly it can´t possibly be used.
-AMD XP 2.0.
Vista runs on a Dual Core 2, E6400. It's a bit faster.
I doubt fast anough.

Anyway, Thanks
regards
--senn