blurry LCD monitor

S

Snonck

I just bought a new 19" LCD monitor (LG L1932P) however, it is blurry
even though I am running it at the native resolution of 1200 x 1024 on
my windows XP (windowsxp) system.

I then plugged my laptop into it to see how it was and it was perfectly
clear. So, it looks like maybe the old AGP graphics card can't drive it
correctly?

I tried to download the latest graphics driver for the card, but the
latest version nvidia driver would not recognise the Riva TNT2 model 64
nvidia graphics card :(

Has anyone got any advice or run across this problem before I try and
get a new video card?
 
R

RJK

Do you mean 1280x1024 pixels ? You said 1200x1024 which would make it
slightly blurry ?

regards, Richard
 
J

JS

Is your refresh rate set correctly for your LCD, which is typically slower
than older CRT monitors?

JS
 
M

Mike Hall - MS MVP Windows Shell/User

You should go to the video card manufacturer website and see if they have
updated drivers and software that will give you the ability to select a
proper widescreen image as opposed to an artificially stretched view..
 
S

Snonck

I tried the nvidia drivers, but the latest wouldn't work so I had to
install some older drivers but that didn't help it either :(
 
R

RJK

LG L1932P doesn't appear to be a widescreen model
http://www.ukgamer.com/index.php4?action=article&id=285&page=1
....and if it was, reasonably recent Nvidia graphics cards / driver software allow you to manually define a screen mode, which is I think what one ends up doing with for example a widescreen 1440x900 pixel LCD monitor !
....which brings me to the point I initially intended to make, ...define your own screen geometry in your Nvidia software "Custom Resolutions and Refresh Rates, if 1280x1024 isn't there - if you can't - time for a new graphics card."

In my view it would be worth buying a newer graphics card with a DVI port AND analogue 15 pin D-sub port on it - if and when the monitor DVI input port dies, you can still use it on analogue - like me until I get my on-site swap out. The picture quality is significantly and noticeably better when injecting the picture into the thing with a DVI signal (direct pixel addressing). ...and using the DVI port, to get the best out of it, you do need the graphics card to be sending the picture along to the monitor in the monitors 'native' mode. i.e. if your monitor has 1280x1024 pixels on it, select 1280x1024 in your graphics cards software/driver, and check that the refresh rate isn't higher that 75hz.
http://uk.lge.com/prodmodeldetail.d...lay=L1932P&unit=NOTHING&model=Select+a+model#

(this post in html due to long URL ...apologies ! :)

regards, Richard
 
J

Jim Macklin

silly thought, is it possible that someone used a chemical
cleaner on the LCD and damaged the screen?



LG L1932P doesn't appear to be a widescreen model
http://www.ukgamer.com/index.php4?action=article&id=285&page=1
....and if it was, reasonably recent Nvidia graphics cards /
driver software allow you to manually define a screen mode,
which is I think what one ends up doing with for example a
widescreen 1440x900 pixel LCD monitor !
....which brings me to the point I initially intended to
make, ...define your own screen geometry in your Nvidia
software "Custom Resolutions and Refresh Rates, if 1280x1024
isn't there - if you can't - time for a new graphics card."

In my view it would be worth buying a newer graphics card
with a DVI port AND analogue 15 pin D-sub port on it - if
and when the monitor DVI input port dies, you can still use
it on analogue - like me until I get my on-site swap out.
The picture quality is significantly and noticeably better
when injecting the picture into the thing with a DVI signal
(direct pixel addressing). ...and using the DVI port, to
get the best out of it, you do need the graphics card to be
sending the picture along to the monitor in the monitors
'native' mode. i.e. if your monitor has 1280x1024 pixels on
it, select 1280x1024 in your graphics cards software/driver,
and check that the refresh rate isn't higher that 75hz.
http://uk.lge.com/prodmodeldetail.d...lay=L1932P&unit=NOTHING&model=Select+a+model#

(this post in html due to long URL ...apologies ! :)

regards, Richard
 
N

[nemielas]

hi,

also try to look what settings are set under "Use the following method to
smooth edges of screen fonts" which you can find at [Control Panel] -
[Display] - [Appearance] - [Effects] and try to alter them.

regards
 
S

Snonck

The screen works fine when plugged into a laptop. The video card is
fairly old and apparently some old video cards don't work too well with
new LCDs :(

It is quite readable, however, when you have a brand new LCD you want
the quality to be perfect.
 
S

Snonck

I don't like using font smoothing and other tricks to make fonts look
round, I just prefer straight sharp fonts even if they are a little
jagged sometimes.



hi,

also try to look what settings are set under "Use the following method to
smooth edges of screen fonts" which you can find at [Control Panel] -
[Display] - [Appearance] - [Effects] and try to alter them.

regards


Snonck said:
I just bought a new 19" LCD monitor (LG L1932P) however, it is blurry even
though I am running it at the native resolution of 1200 x 1024 on my
windows XP (windowsxp) system.

I then plugged my laptop into it to see how it was and it was perfectly
clear. So, it looks like maybe the old AGP graphics card can't drive it
correctly?

I tried to download the latest graphics driver for the card, but the
latest version nvidia driver would not recognise the Riva TNT2 model 64
nvidia graphics card :(

Has anyone got any advice or run across this problem before I try and get
a new video card?
 
B

Bob I

Is "Clear Type" enabled?
I don't like using font smoothing and other tricks to make fonts look
round, I just prefer straight sharp fonts even if they are a little
jagged sometimes.



hi,

also try to look what settings are set under "Use the following method
to smooth edges of screen fonts" which you can find at [Control Panel]
- [Display] - [Appearance] - [Effects] and try to alter them.

regards


I just bought a new 19" LCD monitor (LG L1932P) however, it is blurry
even though I am running it at the native resolution of 1200 x 1024
on my windows XP (windowsxp) system.

I then plugged my laptop into it to see how it was and it was
perfectly clear. So, it looks like maybe the old AGP graphics card
can't drive it correctly?

I tried to download the latest graphics driver for the card, but the
latest version nvidia driver would not recognise the Riva TNT2 model
64 nvidia graphics card :(

Has anyone got any advice or run across this problem before I try and
get a new video card?
 
J

Jim Macklin

new graphics cards are not expensive if you don't want or
need 512 MB graphic RAM. As others have suggested, get a
card with analog and DVI, maybe even a TV tuner such as an
All-in-Wonder card.



| The screen works fine when plugged into a laptop. The
video card is
| fairly old and apparently some old video cards don't work
too well with
| new LCDs :(
|
| It is quite readable, however, when you have a brand new
LCD you want
| the quality to be perfect.
|
|
| Jim Macklin wrote:
| > silly thought, is it possible that someone used a
chemical
| > cleaner on the LCD and damaged the screen?
| >
| >
| >
| > | > LG L1932P doesn't appear to be a widescreen model
| >
http://www.ukgamer.com/index.php4?action=article&id=285&page=1
| > ...and if it was, reasonably recent Nvidia graphics
cards /
| > driver software allow you to manually define a screen
mode,
| > which is I think what one ends up doing with for example
a
| > widescreen 1440x900 pixel LCD monitor !
| > ...which brings me to the point I initially intended to
| > make, ...define your own screen geometry in your Nvidia
| > software "Custom Resolutions and Refresh Rates, if
1280x1024
| > isn't there - if you can't - time for a new graphics
card."
| >
| > In my view it would be worth buying a newer graphics
card
| > with a DVI port AND analogue 15 pin D-sub port on it -
if
| > and when the monitor DVI input port dies, you can still
use
| > it on analogue - like me until I get my on-site swap
out.
| > The picture quality is significantly and noticeably
better
| > when injecting the picture into the thing with a DVI
signal
| > (direct pixel addressing). ...and using the DVI port,
to
| > get the best out of it, you do need the graphics card to
be
| > sending the picture along to the monitor in the monitors
| > 'native' mode. i.e. if your monitor has 1280x1024
pixels on
| > it, select 1280x1024 in your graphics cards
software/driver,
| > and check that the refresh rate isn't higher that 75hz.
| >
http://uk.lge.com/prodmodeldetail.d...lay=L1932P&unit=NOTHING&model=Select+a+model#
| >
| > (this post in html due to long URL ...apologies ! :)
| >
| > regards, Richard
| >
| >
| > | >> I tried the nvidia drivers, but the latest wouldn't
work so
| >> I had to
| >> install some older drivers but that didn't help it
either
| >> :(
| >>
| >>
| >>
| >> Mike Hall - MS MVP Windows Shell/User wrote:
| >>> You should go to the video card manufacturer website
and
| >>> see if they have
| >>> updated drivers and software that will give you the
| >>> ability to select a
| >>> proper widescreen image as opposed to an artificially
| >>> stretched view..
| >>>
| >
 
S

Snonck

No, I have that turned off.



Bob said:
Is "Clear Type" enabled?
I don't like using font smoothing and other tricks to make fonts look
round, I just prefer straight sharp fonts even if they are a little
jagged sometimes.



hi,

also try to look what settings are set under "Use the following
method to smooth edges of screen fonts" which you can find at
[Control Panel] - [Display] - [Appearance] - [Effects] and try to
alter them.

regards



I just bought a new 19" LCD monitor (LG L1932P) however, it is
blurry even though I am running it at the native resolution of 1200
x 1024 on my windows XP (windowsxp) system.

I then plugged my laptop into it to see how it was and it was
perfectly clear. So, it looks like maybe the old AGP graphics card
can't drive it correctly?

I tried to download the latest graphics driver for the card, but the
latest version nvidia driver would not recognise the Riva TNT2 model
64 nvidia graphics card :(

Has anyone got any advice or run across this problem before I try
and get a new video card?
 
A

Alias~-

Snonck said:
No, I have that turned off.

Have you tried turning it on? MS has a tool you can download and install
that will enable you to adjust ClearType. You can use the on line tuner
or download the tool here:

http://www.microsoft.com/typography/cleartype/tuner/Step1.aspx

Alias
Bob said:
Is "Clear Type" enabled?
I don't like using font smoothing and other tricks to make fonts look
round, I just prefer straight sharp fonts even if they are a little
jagged sometimes.



[nemielas] wrote:

hi,

also try to look what settings are set under "Use the following
method to smooth edges of screen fonts" which you can find at
[Control Panel] - [Display] - [Appearance] - [Effects] and try to
alter them.

regards



I just bought a new 19" LCD monitor (LG L1932P) however, it is
blurry even though I am running it at the native resolution of 1200
x 1024 on my windows XP (windowsxp) system.

I then plugged my laptop into it to see how it was and it was
perfectly clear. So, it looks like maybe the old AGP graphics card
can't drive it correctly?

I tried to download the latest graphics driver for the card, but
the latest version nvidia driver would not recognise the Riva TNT2
model 64 nvidia graphics card :(

Has anyone got any advice or run across this problem before I try
and get a new video card?
 
S

Snonck

Yeah downloaded it, installed it and didn't like it. If I can't get
clear sharp fonts then nothing else will help I wouldn't think.



Alias~- said:
Snonck said:
No, I have that turned off.

Have you tried turning it on? MS has a tool you can download and install
that will enable you to adjust ClearType. You can use the on line tuner
or download the tool here:

http://www.microsoft.com/typography/cleartype/tuner/Step1.aspx

Alias
Bob said:
Is "Clear Type" enabled?

Snonck wrote:

I don't like using font smoothing and other tricks to make fonts
look round, I just prefer straight sharp fonts even if they are a
little jagged sometimes.



[nemielas] wrote:

hi,

also try to look what settings are set under "Use the following
method to smooth edges of screen fonts" which you can find at
[Control Panel] - [Display] - [Appearance] - [Effects] and try to
alter them.

regards



I just bought a new 19" LCD monitor (LG L1932P) however, it is
blurry even though I am running it at the native resolution of
1200 x 1024 on my windows XP (windowsxp) system.

I then plugged my laptop into it to see how it was and it was
perfectly clear. So, it looks like maybe the old AGP graphics card
can't drive it correctly?

I tried to download the latest graphics driver for the card, but
the latest version nvidia driver would not recognise the Riva TNT2
model 64 nvidia graphics card :(

Has anyone got any advice or run across this problem before I try
and get a new video card?
 
B

Bob I

Enable it, it was designed specifically for LCD monitors/laptops. I
would suspect that's why it "looks good" plugged into a laptop that
would have it enabled by default.
No, I have that turned off.



Bob said:
Is "Clear Type" enabled?
I don't like using font smoothing and other tricks to make fonts look
round, I just prefer straight sharp fonts even if they are a little
jagged sometimes.



[nemielas] wrote:

hi,

also try to look what settings are set under "Use the following
method to smooth edges of screen fonts" which you can find at
[Control Panel] - [Display] - [Appearance] - [Effects] and try to
alter them.

regards



I just bought a new 19" LCD monitor (LG L1932P) however, it is
blurry even though I am running it at the native resolution of 1200
x 1024 on my windows XP (windowsxp) system.

I then plugged my laptop into it to see how it was and it was
perfectly clear. So, it looks like maybe the old AGP graphics card
can't drive it correctly?

I tried to download the latest graphics driver for the card, but
the latest version nvidia driver would not recognise the Riva TNT2
model 64 nvidia graphics card :(

Has anyone got any advice or run across this problem before I try
and get a new video card?
 
S

Snonck

No, I have it turned off on the laptop as well as I don't like it.



Bob said:
Enable it, it was designed specifically for LCD monitors/laptops. I
would suspect that's why it "looks good" plugged into a laptop that
would have it enabled by default.
No, I have that turned off.



Bob said:
Is "Clear Type" enabled?

Snonck wrote:

I don't like using font smoothing and other tricks to make fonts
look round, I just prefer straight sharp fonts even if they are a
little jagged sometimes.



[nemielas] wrote:

hi,

also try to look what settings are set under "Use the following
method to smooth edges of screen fonts" which you can find at
[Control Panel] - [Display] - [Appearance] - [Effects] and try to
alter them.

regards



I just bought a new 19" LCD monitor (LG L1932P) however, it is
blurry even though I am running it at the native resolution of
1200 x 1024 on my windows XP (windowsxp) system.

I then plugged my laptop into it to see how it was and it was
perfectly clear. So, it looks like maybe the old AGP graphics card
can't drive it correctly?

I tried to download the latest graphics driver for the card, but
the latest version nvidia driver would not recognise the Riva TNT2
model 64 nvidia graphics card :(

Has anyone got any advice or run across this problem before I try
and get a new video card?
 
J

JohnO

Here's what I'd do here...Hook up the laptop again to get the sharp display.
Right-click and see what resolution it's using.

Hook up the desktop and do the same thing. They should match. If they do,
then IMO the desktop video adapter is bad.

I have a spare video card here that's identical to the one I'm using in my
desktop to run my LCD (2nd monitor). Although it's identical, apparently the
timing of the signals coming out is off...the images are not clear and sharp
with this otherwise identical card.

-John O
 

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments. After that, you can post your question and our members will help you out.

Ask a Question

Top