M
Marko Jotic
We just installed Plone on two XP Pro systems, on the old desktop it
comes up fine, on a new IBM laptop it doesn't: we start Plone in the
controller and click the View button, explorer reports "page cannot be
displayed".
We compared the two systems and everything is identical, the Zope
service is running, there is no IIS running, no proxy is set.
using the netstat utility I can see the following:
on the working system these TCP ports appear when I start plone, the
port number (4824) varies:
Local Address Foreign Address State PID
0.0.0.0:80 0.0.0.0:0 LISTENING 2744
0.0.0.0:8080 0.0.0.0:8080 LISTENING 2744
127.0.0.1:4824 127.0.0.1:19999 ESTABLISHED 2744
127.0.0.1:19999 127.0.0.1:4824 ESTABLISHED 2744
when I nanually stop it it takes a few seconds
on the lapttop these TCP ports appear (nothing on 80 and 8080), one at a
time until there are five, the port numbers vary, but they tend to be in
sequence
127.0.0.1:1687 127.0.0.1:19999 TIME_WAIT 0
127.0.0.1:1688 127.0.0.1:19999 TIME_WAIT 0
127.0.0.1:1689 127.0.0.1:19999 TIME_WAIT 0
127.0.0.1:1692 127.0.0.1:19999 TIME_WAIT 0
Eventually they disappear, one at a time, then the plone service stops
When I manually stop it it takes minutes (this is the faster system)
I also tried started the service from the command line, no go
any suggestion? TIA
--
Marko Jotic
"Common sense is anything but common".
From the notebooks of Lazarus Long. Robert A. Heinlein.
Handmade knives, antique designs, exotic materials at
http://www.knifeforging.com/
comes up fine, on a new IBM laptop it doesn't: we start Plone in the
controller and click the View button, explorer reports "page cannot be
displayed".
We compared the two systems and everything is identical, the Zope
service is running, there is no IIS running, no proxy is set.
using the netstat utility I can see the following:
on the working system these TCP ports appear when I start plone, the
port number (4824) varies:
Local Address Foreign Address State PID
0.0.0.0:80 0.0.0.0:0 LISTENING 2744
0.0.0.0:8080 0.0.0.0:8080 LISTENING 2744
127.0.0.1:4824 127.0.0.1:19999 ESTABLISHED 2744
127.0.0.1:19999 127.0.0.1:4824 ESTABLISHED 2744
when I nanually stop it it takes a few seconds
on the lapttop these TCP ports appear (nothing on 80 and 8080), one at a
time until there are five, the port numbers vary, but they tend to be in
sequence
127.0.0.1:1687 127.0.0.1:19999 TIME_WAIT 0
127.0.0.1:1688 127.0.0.1:19999 TIME_WAIT 0
127.0.0.1:1689 127.0.0.1:19999 TIME_WAIT 0
127.0.0.1:1692 127.0.0.1:19999 TIME_WAIT 0
Eventually they disappear, one at a time, then the plone service stops
When I manually stop it it takes minutes (this is the faster system)
I also tried started the service from the command line, no go
any suggestion? TIA
--
Marko Jotic
"Common sense is anything but common".
From the notebooks of Lazarus Long. Robert A. Heinlein.
Handmade knives, antique designs, exotic materials at
http://www.knifeforging.com/