CF Card boot setting problem

G

Guest

Hi, Help needed urgently.

I build a XPE system and it need to run at CF card.

I first format it to NTFS system from windows 2000 system. then copy all the
XPE image files to the cf card. but I can't start the FBA, The error is disk
read error, please tape ctrl-alt-del to restart.

I suspect that may be is the target device setting's problem.
I first set it as multi(0)disk(0)rdisk(0)partition(1), it doesn't work.
then since I check the BIOS setting, I find out the system recognize CF card
as a secondary master hard disk, so I change the seeting to:
multi(0)disk(0)rdisk(2)partition(1) it also doesn't work at all.

Any body knows the correct setting of secondary master IDE device?
Or any step I an doing is wrong?

Please advice. Thanks
 
K

KM

cheqinsy,

From the error message you mentioned below it doesn't seem you got even boot sector loaded.
You can easy verify that if you set a non-zero timeout in your boot.ini. If you can see the boot menu, ntldr got loaded which means
the NTFS boot sector was loaded too. If you don't, you are not that far yet and you have to properly partition and format the card.

A couple of things to keep in mind when you are formatting a CF card:
- best is to use manufacturer supplied formatting tools
- if you don't have the above, format the card on the target device (e.g., from WINPE booted). *always* format storage devices
on target.
- if doesn't help, switch to DOS (real DOS e.g. 6.22 or 7.0, not command prompt in Windows) and boot it on the target (floppy,
CD, another hard drive, etc.). Partition and format the card there using fdisk and format DOS utilities.
 
G

Guest

I have tried boot from dos and format The CF CARD, the system will be FAT not
NTFS. If I need to change the NTLoder to EWFLoder, is it possible to have the
EWF function under the FAT system?

thanks
 
S

Sean Liming \(eMVP\)

The boot sector and loader are not the same. You can run EWF on either FAT
or NTFS. If you prepare the disk with DOS, Bootprep must be used to change
he boot sector from DOS boot sector to NT Boot sector.

Sounds like your CF is ID'd as removable. If you want to format with NTFS,
the flash disk should be ID'd as fixed and placed in a IDE-to-CF adapter in
a Windows 2000 or XP system. Using a USB-to-CF, formating a CF card will not
lay down the boot sector because 2000 and XP think the card is only for used
removable media and not boot.

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
 
G

Guest

hi, thanks for the instruction.

My CF card is settng as the secondary master hard disk. not removable disk.
As you advised, I can boot up using dos, and perform fdisk and format c:,
then bootprep /dc. after that copy all the file to the CF card. The XPE
system should add the FAT component not NTFS, Am I right? Please advise.

Thanks.
 
K

KM

Just to add a couple more points here.

If you are planning on using EWF RAM or RAM Reg mode but not Disk Overlay nor special features like HORM, your loader can be ntldr.
Also, with CF protected by EWF it is advised to use FAT instead of NTFS as the latter is more chattier than plain FAT. In other
words, you're going to waste your overlay space on file system related and unnecessary on protected volume activities if you go with
NTFS.

If NTFS is a hard requirement for you and you can only make the card bootable from DOS (that may be the case with some cards on the
market). You can always convert CF volume to NTFS later, after you lay down the OS image there or whatever data you are planning on
having there. To do that you will need to use convert.exe.

Yes, you must have FAT component added to your image configuration. It is often easier to have both FS components added there since
the footprint hit is relatively small.
 
G

Guest

Hi, Dear Sir,
Follow your instruction to build my XPE image and copied over to the CF
card, But I got the blue screen.

*** Stop: 0x0000007B (0XF99AC528,0X00000000E, 0X00000000, 0X00000000)
Don't know what's wrong.

Any Hint? Thanks
 
G

Guest

I have installed XP professional into my actual target machine, and run a
tap.exe get the PMQ file, When I build the XPE System. I have got some error
list as following:

R: Building: "Intel(R) 82852/82855 GM/GME Graphics Controller [Version
6.14.10.3751, R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.inf"
R: Error 1005: File not found: "ialmnt5.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.sys"
R: Error 1005: File not found: "ialmnt5.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrnt5.dll"
R: Error 1005: File not found: "ialmrnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdnt5.dll"
R: Error 1005: File not found: "ialmdnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdev5.dll"
R: Error 1005: File not found: "ialmdev5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdd5.dll"
R: Error 1005: File not found: "ialmdd5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"oemdspif.dll"
R: Error 1005: File not found: "oemdspif.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrem.dll"
R: Error 1005: File not found: "ialmrem.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgicd.dll"
R: Error 1005: File not found: "ialmgicd.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgdev.dll"
R: Error 1005: File not found: "ialmgdev.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"iAlmCoIn.dll"
R: Error 1005: File not found: "iAlmCoIn.dll"
...........
R: Building: "Intel(R) PRO/100 VE Network Connection [Version 7.0.26, R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100b325.inf"
R: Error 1005: File not found: "e100b325.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"IntelNic.dll"
R: Error 1005: File not found: "IntelNic.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100bmsg.dll"
R: Error 1005: File not found: "e100bmsg.dll"
............

R: Building: "Speech API Core [Version 5.1.2600.2180, R2890]"...
R: Error 1004: Invalid resource:
"RegKey(819):"HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Speech\Voices\Preview"":
(Error 5 (0x5) in "Microsoft VBScript runtime error": Invalid procedure call
or argument)
...........
R: Building: "Vinyl AC'97 Codec Combo Driver (WDM) [Version 6.14.01.4000,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"VIAComp.inf"
R: Error 1005: File not found: "VIAComp.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viaudios.sys"
R: Error 1005: File not found: "viaudios.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viasens.sys"
R: Error 1005: File not found: "viasens.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"crlds3d.dll"
R: Error 1005: File not found: "crlds3d.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"Audio3D.dll"
R: Error 1005: File not found: "Audio3D.dll"

THEN After FBA I get this Stop error.
What I should do?
Please Help Me. Thanks
 
S

Sean Liming \(eMVP\)

1. You are getting the errors because the Components and Repositories for
the different device drivers are not linked. If you created these driver
components, edit the SLDs and look in the settings page for each component.
If there is an Unknown next to repository, then you need to make the link to
the Respository.

2. What Stop Error are you getting 0x7B?


Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
XP Training Class Nov 28-30 - http://www.sjjmicro.com/Training.html



cheqinsy said:
I have installed XP professional into my actual target machine, and run a
tap.exe get the PMQ file, When I build the XPE System. I have got some
error
list as following:

R: Building: "Intel(R) 82852/82855 GM/GME Graphics Controller [Version
6.14.10.3751, R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.inf"
R: Error 1005: File not found: "ialmnt5.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.sys"
R: Error 1005: File not found: "ialmnt5.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrnt5.dll"
R: Error 1005: File not found: "ialmrnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdnt5.dll"
R: Error 1005: File not found: "ialmdnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdev5.dll"
R: Error 1005: File not found: "ialmdev5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdd5.dll"
R: Error 1005: File not found: "ialmdd5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"oemdspif.dll"
R: Error 1005: File not found: "oemdspif.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrem.dll"
R: Error 1005: File not found: "ialmrem.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgicd.dll"
R: Error 1005: File not found: "ialmgicd.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgdev.dll"
R: Error 1005: File not found: "ialmgdev.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"iAlmCoIn.dll"
R: Error 1005: File not found: "iAlmCoIn.dll"
..........
R: Building: "Intel(R) PRO/100 VE Network Connection [Version 7.0.26,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100b325.inf"
R: Error 1005: File not found: "e100b325.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"IntelNic.dll"
R: Error 1005: File not found: "IntelNic.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100bmsg.dll"
R: Error 1005: File not found: "e100bmsg.dll"
...........

R: Building: "Speech API Core [Version 5.1.2600.2180, R2890]"...
R: Error 1004: Invalid resource:
"RegKey(819):"HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Speech\Voices\Preview"":
(Error 5 (0x5) in "Microsoft VBScript runtime error": Invalid procedure
call
or argument)
..........
R: Building: "Vinyl AC'97 Codec Combo Driver (WDM) [Version 6.14.01.4000,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"VIAComp.inf"
R: Error 1005: File not found: "VIAComp.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viaudios.sys"
R: Error 1005: File not found: "viaudios.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viasens.sys"
R: Error 1005: File not found: "viasens.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"crlds3d.dll"
R: Error 1005: File not found: "crlds3d.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"Audio3D.dll"
R: Error 1005: File not found: "Audio3D.dll"

THEN After FBA I get this Stop error.
What I should do?
Please Help Me. Thanks

Sean Liming (eMVP) said:
Probably a missing component, some Stop 7B solutions can be found here:
http://www.seanliming.com/Docs/XPE Stop 0x0000007B Error V1.2.pdf
http://www.seanliming.com/Articles.html

Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
Click to expand...
Click to expand...
 
G

Guest

Thanks, Sean,
I am getting Stop: 0x0000007B (0XF99AC528,0X00000000E, 0X00000000,
0X00000000) error.

Sean Liming (eMVP) said:
1. You are getting the errors because the Components and Repositories for
the different device drivers are not linked. If you created these driver
components, edit the SLDs and look in the settings page for each component.
If there is an Unknown next to repository, then you need to make the link to
the Respository.

2. What Stop Error are you getting 0x7B?


Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
XP Training Class Nov 28-30 - http://www.sjjmicro.com/Training.html



cheqinsy said:
I have installed XP professional into my actual target machine, and run a
tap.exe get the PMQ file, When I build the XPE System. I have got some
error
list as following:

R: Building: "Intel(R) 82852/82855 GM/GME Graphics Controller [Version
6.14.10.3751, R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.inf"
R: Error 1005: File not found: "ialmnt5.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.sys"
R: Error 1005: File not found: "ialmnt5.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrnt5.dll"
R: Error 1005: File not found: "ialmrnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdnt5.dll"
R: Error 1005: File not found: "ialmdnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdev5.dll"
R: Error 1005: File not found: "ialmdev5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdd5.dll"
R: Error 1005: File not found: "ialmdd5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"oemdspif.dll"
R: Error 1005: File not found: "oemdspif.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrem.dll"
R: Error 1005: File not found: "ialmrem.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgicd.dll"
R: Error 1005: File not found: "ialmgicd.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgdev.dll"
R: Error 1005: File not found: "ialmgdev.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"iAlmCoIn.dll"
R: Error 1005: File not found: "iAlmCoIn.dll"
..........
R: Building: "Intel(R) PRO/100 VE Network Connection [Version 7.0.26,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100b325.inf"
R: Error 1005: File not found: "e100b325.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"IntelNic.dll"
R: Error 1005: File not found: "IntelNic.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100bmsg.dll"
R: Error 1005: File not found: "e100bmsg.dll"
...........

R: Building: "Speech API Core [Version 5.1.2600.2180, R2890]"...
R: Error 1004: Invalid resource:
"RegKey(819):"HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Speech\Voices\Preview"":
(Error 5 (0x5) in "Microsoft VBScript runtime error": Invalid procedure
call
or argument)
..........
R: Building: "Vinyl AC'97 Codec Combo Driver (WDM) [Version 6.14.01.4000,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"VIAComp.inf"
R: Error 1005: File not found: "VIAComp.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viaudios.sys"
R: Error 1005: File not found: "viaudios.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viasens.sys"
R: Error 1005: File not found: "viasens.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"crlds3d.dll"
R: Error 1005: File not found: "crlds3d.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"Audio3D.dll"
R: Error 1005: File not found: "Audio3D.dll"

THEN After FBA I get this Stop error.
What I should do?
Please Help Me. Thanks

Sean Liming (eMVP) said:
Probably a missing component, some Stop 7B solutions can be found here:
http://www.seanliming.com/Docs/XPE Stop 0x0000007B Error V1.2.pdf
http://www.seanliming.com/Articles.html

Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit


Hi, Dear Sir,
Follow your instruction to build my XPE image and copied over to the CF
card, But I got the blue screen.

*** Stop: 0x0000007B (0XF99AC528,0X00000000E, 0X00000000, 0X00000000)
Don't know what's wrong.

Any Hint? Thanks
Click to expand...
Click to expand...
Click to expand...
 
S

Sean Liming \(eMVP\)

Since it is Stop 0x7B, take a look at the paper I wrote and see if there is
a missing component.

Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
XP Training Class Nov 28-30 - http://www.sjjmicro.com/Training.html



cheqinsy said:
Thanks, Sean,
I am getting Stop: 0x0000007B (0XF99AC528,0X00000000E, 0X00000000,
0X00000000) error.

Sean Liming (eMVP) said:
1. You are getting the errors because the Components and Repositories for
the different device drivers are not linked. If you created these driver
components, edit the SLDs and look in the settings page for each
component.
If there is an Unknown next to repository, then you need to make the link
to
the Respository.

2. What Stop Error are you getting 0x7B?


Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
XP Training Class Nov 28-30 - http://www.sjjmicro.com/Training.html



cheqinsy said:
I have installed XP professional into my actual target machine, and run
a
tap.exe get the PMQ file, When I build the XPE System. I have got some
error
list as following:

R: Building: "Intel(R) 82852/82855 GM/GME Graphics Controller [Version
6.14.10.3751, R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.inf"
R: Error 1005: File not found: "ialmnt5.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.sys"
R: Error 1005: File not found: "ialmnt5.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrnt5.dll"
R: Error 1005: File not found: "ialmrnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdnt5.dll"
R: Error 1005: File not found: "ialmdnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdev5.dll"
R: Error 1005: File not found: "ialmdev5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdd5.dll"
R: Error 1005: File not found: "ialmdd5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"oemdspif.dll"
R: Error 1005: File not found: "oemdspif.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrem.dll"
R: Error 1005: File not found: "ialmrem.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgicd.dll"
R: Error 1005: File not found: "ialmgicd.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgdev.dll"
R: Error 1005: File not found: "ialmgdev.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"iAlmCoIn.dll"
R: Error 1005: File not found: "iAlmCoIn.dll"
..........
R: Building: "Intel(R) PRO/100 VE Network Connection [Version 7.0.26,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100b325.inf"
R: Error 1005: File not found: "e100b325.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"IntelNic.dll"
R: Error 1005: File not found: "IntelNic.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100bmsg.dll"
R: Error 1005: File not found: "e100bmsg.dll"
...........

R: Building: "Speech API Core [Version 5.1.2600.2180, R2890]"...
R: Error 1004: Invalid resource:
"RegKey(819):"HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Speech\Voices\Preview"":
(Error 5 (0x5) in "Microsoft VBScript runtime error": Invalid procedure
call
or argument)
..........
R: Building: "Vinyl AC'97 Codec Combo Driver (WDM) [Version
6.14.01.4000,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"VIAComp.inf"
R: Error 1005: File not found: "VIAComp.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viaudios.sys"
R: Error 1005: File not found: "viaudios.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viasens.sys"
R: Error 1005: File not found: "viasens.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"crlds3d.dll"
R: Error 1005: File not found: "crlds3d.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"Audio3D.dll"
R: Error 1005: File not found: "Audio3D.dll"

THEN After FBA I get this Stop error.
What I should do?
Please Help Me. Thanks

:


Probably a missing component, some Stop 7B solutions can be found
here:
http://www.seanliming.com/Docs/XPE Stop 0x0000007B Error V1.2.pdf
http://www.seanliming.com/Articles.html

Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded
Supplemental
Toolkit


Hi, Dear Sir,
Follow your instruction to build my XPE image and copied over to the
CF
card, But I got the blue screen.

*** Stop: 0x0000007B (0XF99AC528,0X00000000E, 0X00000000,
0X00000000)
Don't know what's wrong.

Any Hint? Thanks
Click to expand...
Click to expand...
Click to expand...
 
G

Guest

Hi, Mr Sean

I have using winlogon sample macro componenent to build a system it is
bootable. But with no function inside. When I add some devices, it will show
the blue screen. any idea about how to trace the error source?

Thanks

Sean Liming (eMVP) said:
Since it is Stop 0x7B, take a look at the paper I wrote and see if there is
a missing component.

Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
XP Training Class Nov 28-30 - http://www.sjjmicro.com/Training.html



cheqinsy said:
Thanks, Sean,
I am getting Stop: 0x0000007B (0XF99AC528,0X00000000E, 0X00000000,
0X00000000) error.

Sean Liming (eMVP) said:
1. You are getting the errors because the Components and Repositories for
the different device drivers are not linked. If you created these driver
components, edit the SLDs and look in the settings page for each
component.
If there is an Unknown next to repository, then you need to make the link
to
the Respository.

2. What Stop Error are you getting 0x7B?


Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
XP Training Class Nov 28-30 - http://www.sjjmicro.com/Training.html



I have installed XP professional into my actual target machine, and run
a
tap.exe get the PMQ file, When I build the XPE System. I have got some
error
list as following:

R: Building: "Intel(R) 82852/82855 GM/GME Graphics Controller [Version
6.14.10.3751, R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.inf"
R: Error 1005: File not found: "ialmnt5.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.sys"
R: Error 1005: File not found: "ialmnt5.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrnt5.dll"
R: Error 1005: File not found: "ialmrnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdnt5.dll"
R: Error 1005: File not found: "ialmdnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdev5.dll"
R: Error 1005: File not found: "ialmdev5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdd5.dll"
R: Error 1005: File not found: "ialmdd5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"oemdspif.dll"
R: Error 1005: File not found: "oemdspif.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrem.dll"
R: Error 1005: File not found: "ialmrem.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgicd.dll"
R: Error 1005: File not found: "ialmgicd.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgdev.dll"
R: Error 1005: File not found: "ialmgdev.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"iAlmCoIn.dll"
R: Error 1005: File not found: "iAlmCoIn.dll"
..........
R: Building: "Intel(R) PRO/100 VE Network Connection [Version 7.0.26,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100b325.inf"
R: Error 1005: File not found: "e100b325.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"IntelNic.dll"
R: Error 1005: File not found: "IntelNic.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100bmsg.dll"
R: Error 1005: File not found: "e100bmsg.dll"
...........

R: Building: "Speech API Core [Version 5.1.2600.2180, R2890]"...
R: Error 1004: Invalid resource:
"RegKey(819):"HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Speech\Voices\Preview"":
(Error 5 (0x5) in "Microsoft VBScript runtime error": Invalid procedure
call
or argument)
..........
R: Building: "Vinyl AC'97 Codec Combo Driver (WDM) [Version
6.14.01.4000,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"VIAComp.inf"
R: Error 1005: File not found: "VIAComp.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viaudios.sys"
R: Error 1005: File not found: "viaudios.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viasens.sys"
R: Error 1005: File not found: "viasens.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"crlds3d.dll"
R: Error 1005: File not found: "crlds3d.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"Audio3D.dll"
R: Error 1005: File not found: "Audio3D.dll"

THEN After FBA I get this Stop error.
What I should do?
Please Help Me. Thanks

:


Probably a missing component, some Stop 7B solutions can be found
here:
http://www.seanliming.com/Docs/XPE Stop 0x0000007B Error V1.2.pdf
http://www.seanliming.com/Articles.html

Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded
Supplemental
Toolkit


Hi, Dear Sir,
Follow your instruction to build my XPE image and copied over to the
CF
card, But I got the blue screen.

*** Stop: 0x0000007B (0XF99AC528,0X00000000E, 0X00000000,
0X00000000)
Don't know what's wrong.

Any Hint? Thanks
Click to expand...
Click to expand...
Click to expand...
 
S

Stuart Langley

Missing dependancies. Use the /sos flag and /noguiboot to give an
approximate trace of where it dies. If this does not provide enough
information then you may need to swith to kernel debugger.

Also, is the blue screen during the FBA process or after?

Also, looking at your post below you have not copied the files for the
additional drivers you require into the database correctly, so they are not
included in your image. Make sure you get no error at the end of the image
build process.

Stuart

cheqinsy said:
Hi, Mr Sean

I have using winlogon sample macro componenent to build a system it is
bootable. But with no function inside. When I add some devices, it will
show
the blue screen. any idea about how to trace the error source?

Thanks

Sean Liming (eMVP) said:
Since it is Stop 0x7B, take a look at the paper I wrote and see if there
is
a missing component.

Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded Supplemental
Toolkit
XP Training Class Nov 28-30 - http://www.sjjmicro.com/Training.html



cheqinsy said:
Thanks, Sean,
I am getting Stop: 0x0000007B (0XF99AC528,0X00000000E, 0X00000000,
0X00000000) error.

:


1. You are getting the errors because the Components and Repositories
for
the different device drivers are not linked. If you created these
driver
components, edit the SLDs and look in the settings page for each
component.
If there is an Unknown next to repository, then you need to make the
link
to
the Respository.

2. What Stop Error are you getting 0x7B?


Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded
Supplemental
Toolkit
XP Training Class Nov 28-30 - http://www.sjjmicro.com/Training.html



I have installed XP professional into my actual target machine, and
run
a
tap.exe get the PMQ file, When I build the XPE System. I have got
some
error
list as following:

R: Building: "Intel(R) 82852/82855 GM/GME Graphics Controller
[Version
6.14.10.3751, R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.inf"
R: Error 1005: File not found: "ialmnt5.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmnt5.sys"
R: Error 1005: File not found: "ialmnt5.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrnt5.dll"
R: Error 1005: File not found: "ialmrnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdnt5.dll"
R: Error 1005: File not found: "ialmdnt5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdev5.dll"
R: Error 1005: File not found: "ialmdev5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmdd5.dll"
R: Error 1005: File not found: "ialmdd5.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"oemdspif.dll"
R: Error 1005: File not found: "oemdspif.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmrem.dll"
R: Error 1005: File not found: "ialmrem.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgicd.dll"
R: Error 1005: File not found: "ialmgicd.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"ialmgdev.dll"
R: Error 1005: File not found: "ialmgdev.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"iAlmCoIn.dll"
R: Error 1005: File not found: "iAlmCoIn.dll"
..........
R: Building: "Intel(R) PRO/100 VE Network Connection [Version
7.0.26,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100b325.inf"
R: Error 1005: File not found: "e100b325.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"IntelNic.dll"
R: Error 1005: File not found: "IntelNic.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"e100bmsg.dll"
R: Error 1005: File not found: "e100bmsg.dll"
...........

R: Building: "Speech API Core [Version 5.1.2600.2180, R2890]"...
R: Error 1004: Invalid resource:
"RegKey(819):"HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Speech\Voices\Preview"":
(Error 5 (0x5) in "Microsoft VBScript runtime error": Invalid
procedure
call
or argument)
..........
R: Building: "Vinyl AC'97 Codec Combo Driver (WDM) [Version
6.14.01.4000,
R7]"...
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"VIAComp.inf"
R: Error 1005: File not found: "VIAComp.inf"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viaudios.sys"
R: Error 1005: File not found: "viaudios.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"viasens.sys"
R: Error 1005: File not found: "viasens.sys"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"crlds3d.dll"
R: Error 1005: File not found: "crlds3d.dll"
Error 1005 (0x3ED) in "PlatformLib::CopySrcFile2": File not found:
"Audio3D.dll"
R: Error 1005: File not found: "Audio3D.dll"

THEN After FBA I get this Stop error.
What I should do?
Please Help Me. Thanks

:


Probably a missing component, some Stop 7B solutions can be found
here:
http://www.seanliming.com/Docs/XPE Stop 0x0000007B Error V1.2.pdf
http://www.seanliming.com/Articles.html

Regards,

Sean Liming
www.sjjmicro.com / www.seanliming.com
XP Embedded Book Author - XP Embedded Advanced, XP Embedded
Supplemental
Toolkit


Hi, Dear Sir,
Follow your instruction to build my XPE image and copied over to
the
CF
card, But I got the blue screen.

*** Stop: 0x0000007B (0XF99AC528,0X00000000E, 0X00000000,
0X00000000)
Don't know what's wrong.

Any Hint? Thanks
Click to expand...
Click to expand...
Click to expand...
 

Ask a Question

Want to reply to this thread or ask your own question?

You'll need to choose a username for the site, which only take a couple of moments. After that, you can post your question and our members will help you out.

Ask a Question

Similar Threads

CF boot issue 0
EWF on CF as IDE-0 (secondary) boot problem 5
Multi-Boot with EWF 11
CF Disk - partitioning and formatting 8
Windows XP Embedded Cloning - 2 Partitions Display 0
update image on cf-card by usb stick 1
boot / boot.ini question 2
Problems booting copied image from CF card 2

Top