Restoring a PST File

  • Thread starter Thread starter Michael
  • Start date Start date
M

Michael

Further to my previous Posts.
1. I have backed up the outlook.pst file to CD using NERO
2. I have restored the same outlook.pst file to a
seperate folder
3. I have checked the file attribute and made sure the
archive bit is off
4. I have run the scanpst program over the outlook.pst
file.

SCANPST came up with a large number of errors (I have the
file). An example is:
!!PMap page @6112768: PTYPE mismatch (read 00, expected
83)
!!PMap page @6112768: BID mismatch (read 0, expected
5D4600)

When I open or import the outlook.pst file, there are 2
empty folders... recovered and deleted.

Any suggestions as to what went wrong?

Thanks in advance

Michael
 
Michael said:
Further to my previous Posts.
1. I have backed up the outlook.pst file to CD using NERO
Click to expand...

If you have Windows XP, just copy it to the CD device.
2. I have restored the same outlook.pst file to a
seperate folder
Click to expand...

How? Just drag-and-drop.
3. I have checked the file attribute and made sure the
archive bit is off
Click to expand...

Not relevent. Make sure the Read-Only attribute is off.
 
-----Original Message-----
NERO

If you have Windows XP, just copy it to the CD device.


How? Just drag-and-drop.


Not relevent. Make sure the Read-Only attribute is off.
Click to expand...
Brian,
Yes, I dragged and dropped.
The Read Only was set off before the attempt to restore.

Michael
 
Yes, I dragged and dropped.
Click to expand...

Then why did you say in your original post:
1. I have backed up the outlook.pst file to CD using NERO
Click to expand...

This implies that you started the Nero application, pointed it at the PST
and then burned it to the CD. Did you try using Windows' built-in CD
burning?
The Read Only was set off before the attempt to restore.
Click to expand...

In your OP you said:
2. I have restored the same outlook.pst file to a seperate folder
Click to expand...

You must remove the read-only _after_ restoring the PST to your hard drive.
You cannot remove it _before_ the restore, as you state you did above, since
CDs don't allow read/write access to files they contain.

No where in your original post does it say you first copied the PST to HD
and then remove the read-only attribute.

Please list exactly all steps you used to try to move the PST. Start at the
very beginning.
 
-----Original Message-----
(e-mail address removed)

Then why did you say in your original post:
NERO

This implies that you started the Nero application, pointed it at the PST
and then burned it to the CD. Did you try using Windows' built-in CD
burning?
restore.

In your OP you said:
seperate folder

You must remove the read-only _after_ restoring the PST to your hard drive.
You cannot remove it _before_ the restore, as you state you did above, since
CDs don't allow read/write access to files they contain.

No where in your original post does it say you first copied the PST to HD
and then remove the read-only attribute.

Please list exactly all steps you used to try to move the PST. Start at the
very beginning.
Click to expand...
OK Brian, The exact steps.
1. Ended Outlook
2. Started Nero Express and burnt the PST file to the CD.
3. Dragged and Dropped the PST file from the CD to a
seperate folder on the PC. The PST file is 282MB.
3. I changed the file attributes and removed the archive
and read only attributes to blank.
4. I opened Outlook and tried to open the restored PST
file and failed.
5. I ran the SCANPST and had errors.
6. I opened the PST file with Outlook and had no mail
available.

Thanks

Michael
 
OK Brian, The exact steps.
1. Ended Outlook
Click to expand...

Did you verify that Outlook was actually closed by checking in the task list
in Task Manager?
2. Started Nero Express and burnt the PST file to the CD.
Click to expand...

I suspect that this is where the corruption occurred. Either the PST wasn't
closed or Nero corrupted it. Is this a Windows XP machine? If so, try
using Windows' built-in burning.
3. Dragged and Dropped the PST file from the CD to a
seperate folder on the PC. The PST file is 282MB.
3. I changed the file attributes and removed the archive
and read only attributes to blank.
Click to expand...

The archive attribute can remain set, but remoing it should have no effect.
Of course, you did the correct thing with the read-only attribute.
4. I opened Outlook and tried to open the restored PST
file and failed.
Click to expand...

How? Did you use File>Open?
 
Brian,
I will have to visit the guy and recheck everything from
scratch.
I will repost next week.

regards

Michael
 
Back
Top