G
Guest
Hi
I tried out the procedure in MSDN help to create a bootable CD(Windows embedded XP)
I got the image (By including the components mentioned) , prepared the pre FBA CD ,Put the image on 650MB Fat Primary partition(I used only 1 hard disk of 20 GB) .The remaining partion is unallocated
The system reboots twice as mentioned
But in the FBAlog.txt the Eltorito CD is not detected .The following is the messag
ConfigureEwf() Start
5:50:40 AM - Getting EWF config parameters from registry
5:50:40 AM - EWF Partition Size = 0 (KBytes), Levels = 1, Volumes = 1
5:50:40 AM - Protected Volume Config #0
5:50:40 AM - Disk= 0,Part= 1,DiskType= IDE,Type= RAM
5:50:40 AM - Enable= Disabled, Optimize= 0, LazyWrite= N
5:50:40 AM - Found 1 Hard Disks
5:50:40 AM - Searching for El Torito disk
5:50:40 AM - Disk0 signature = 0x80
5:50:40 AM - Checking Start value in System\CurrentControlSet\Services\redbook key
5:50:40 AM - Resetting Start value
5:50:40 AM - Checking Start value in System\CurrentControlSet\Services\Imapi key
5:50:40 AM - Deleting EWF Partition #2, disk#=0, type=6
5:50:40 AM - Disk #0 layout info
5:50:40 AM - PRIMARY partition,start=0x0000000000007e00, len=0x0000000028b0a800, type= 6
5:50:40 AM - FREE partition,start=0x0000000028b12600, len=0x0000000356881e00, type= 0
5:50:40 AM - Allocating EWF in PRIMARY partition, start=0x0000000028b12600, len=0x000000000000fc00.
5:50:40 AM - Created EWF partition on Disk = 0, partition = 2,size = 0x000000000000fc00
5:50:40 AM - ewfOpen
5:50:40 AM - EWF Volume Config on Disk#0, Partition#2
5:50:40 AM - Segments = 0, Max Volumes = 1, Max Levels = 1
5:50:40 AM - ewfAdd.
5:50:40 AM - Protected Volume Config on Disk0\Partition1
5:50:40 AM - Type = RAM, State= DISABLED
5:50:40 AM - ewfClose
5:50:41 AM - Saving EWF configuration to registry
5:50:41 AM - Protected Volume ArcName = multi(0)disk(0)rdisk(0)partition(1)
5:50:41 AM - ConfigureEwf() End, status = 0x0
The end status is 0 but When after running Etprep/all on this volume and obtaining the final iso image on CD
The system does not boot from this CD
Please help me
Thanks and Regard
Abhik
I tried out the procedure in MSDN help to create a bootable CD(Windows embedded XP)
I got the image (By including the components mentioned) , prepared the pre FBA CD ,Put the image on 650MB Fat Primary partition(I used only 1 hard disk of 20 GB) .The remaining partion is unallocated
The system reboots twice as mentioned
But in the FBAlog.txt the Eltorito CD is not detected .The following is the messag
ConfigureEwf() Start
5:50:40 AM - Getting EWF config parameters from registry
5:50:40 AM - EWF Partition Size = 0 (KBytes), Levels = 1, Volumes = 1
5:50:40 AM - Protected Volume Config #0
5:50:40 AM - Disk= 0,Part= 1,DiskType= IDE,Type= RAM
5:50:40 AM - Enable= Disabled, Optimize= 0, LazyWrite= N
5:50:40 AM - Found 1 Hard Disks
5:50:40 AM - Searching for El Torito disk
5:50:40 AM - Disk0 signature = 0x80
5:50:40 AM - Checking Start value in System\CurrentControlSet\Services\redbook key
5:50:40 AM - Resetting Start value
5:50:40 AM - Checking Start value in System\CurrentControlSet\Services\Imapi key
5:50:40 AM - Deleting EWF Partition #2, disk#=0, type=6
5:50:40 AM - Disk #0 layout info
5:50:40 AM - PRIMARY partition,start=0x0000000000007e00, len=0x0000000028b0a800, type= 6
5:50:40 AM - FREE partition,start=0x0000000028b12600, len=0x0000000356881e00, type= 0
5:50:40 AM - Allocating EWF in PRIMARY partition, start=0x0000000028b12600, len=0x000000000000fc00.
5:50:40 AM - Created EWF partition on Disk = 0, partition = 2,size = 0x000000000000fc00
5:50:40 AM - ewfOpen
5:50:40 AM - EWF Volume Config on Disk#0, Partition#2
5:50:40 AM - Segments = 0, Max Volumes = 1, Max Levels = 1
5:50:40 AM - ewfAdd.
5:50:40 AM - Protected Volume Config on Disk0\Partition1
5:50:40 AM - Type = RAM, State= DISABLED
5:50:40 AM - ewfClose
5:50:41 AM - Saving EWF configuration to registry
5:50:41 AM - Protected Volume ArcName = multi(0)disk(0)rdisk(0)partition(1)
5:50:41 AM - ConfigureEwf() End, status = 0x0
The end status is 0 but When after running Etprep/all on this volume and obtaining the final iso image on CD
The system does not boot from this CD
Please help me
Thanks and Regard
Abhik