error => isass.exe

  • Thread starter Thread starter Guest
  • Start date Start date
G

Guest

hell

I make a el torito cd of windows xp

when I boot from a el torito cdr I have the message

Isass.ex
An I/O operation initiated by the registry failed unrecoverly. The registry
could not read in, or write out, or flush, one of the files that contain the system
image of the registry


if you know this error answer m

regards,
 
Have you tested RAM EWF on first partition after you deleted extra EWF
config partition?

This could be a problem with EWF that is not working on image that is booted
from CD.

Regards,
Slobodan
 
I have for => ewfmgr c:
Protected Volume Configuratio
Type RA
State ENABLE
Volume ID D7 FD A2 9A 00 7E 0
Device Name "\Device\HarddiskVol
Max Levels
Clump Size 51
Current Level
Memory used for data 7642112 byte
Memory used for mapping 4096 byte

and with
 
ewfmgr C:

But how did you configured EWF.
Have you used my solution from www.xpefiles.com or do you have extra config
partition created.
If you have extra partition.
You need to delete it, and then to test if EWF is working.

Regards,
Slobodan
 
I have 2 hard disc

The first with XP + Target Designer
and I use the second to make xpe ( partition : 600 Mo)

I do like you says but without result Always Isass.exe
error

I do like he says at
http://msdn.microsoft.com/library/default.asp?
url=/library/en-
us/xpehelp/html/xetbshowtocreatecompactflashrun-
timeimage.asp in the "How to Create a Bootable CD-ROM"

When I reboot for the FBA I have only the disc with XPE
and the cd

After the FBA I have :

=>fbalog
15:51:07 - ConfigureEwf() Start.
15:51:07 - Getting EWF config parameters from registry.
15:51:07 - EWF Partition Size = 0 (KBytes), Levels = 1,
Volumes = 1.
15:51:07 - Protected Volume Config #0 :
15:51:07 - Disk= 0,Part= 1,DiskType= IDE,Type= RAM.
15:51:07 - Enable= Disabled, Optimize= 2, LazyWrite=
N.
15:51:07 - Found 1 Hard Disks.
15:51:07 - Searching for El Torito disk.
15:51:07 - Disk0 signature = 0x9AA2FDD7.
15:51:07 - Checking Start value in
System\CurrentControlSet\Services\redbook key.
15:51:07 - Resetting Start value.
15:51:07 - Checking Start value in
System\CurrentControlSet\Services\Imapi key.
15:51:07 - Disk #0 layout info:
15:51:07 - PRIMARY partition,start=0x0000000000007e00,
len=0x0000000025bf9c00, type= 6
15:51:07 - FREE partition,start=0x0000000025c01a00,
len=0x000000092b636800, type= 0
15:51:07 - Allocating EWF in PRIMARY partition,
start=0x0000000025c01a00, len=0x000000000000fc00.
15:51:07 - Created EWF partition on Disk = 0, partition
= 2,size = 0x000000000000fc00 .
15:51:07 - ewfOpen.
15:51:07 - EWF Volume Config on Disk#0, Partition#2:
15:51:07 - Segments = 0, Max Volumes = 1, Max Levels
= 1
15:51:07 - ewfAdd.
15:51:07 - Protected Volume Config on Disk0
\Partition1 :
15:51:07 - Type = RAM, State= DISABLED.
15:51:07 - ewfClose
15:51:07 - Saving EWF configuration to registry:
15:51:07 - Protected Volume ArcName = multi(0)disk(0)
rdisk(0)partition(1).
15:51:07 - ConfigureEwf() End, status = 0x0.
15:51:07 - [CallEntryPointThread] C:\WINDOWS\system32
\ewfdll.dll, ConfigureEwf
15:51:07 - [FBASetProgressText] Resetting Setup Flag...
15:51:10 - [FBADoReboot] Sleeping...
15:51:20 - [FBADoReboot] Rebooting system...
16:16:12 - [FBASetProgressText] Resetting Setup Flag...
16:16:12 - [DoFBA] FBAProcessDLLsInOrder failed!

=> C:\WINDOWS\system32>ewfmgr
The Ewf Volume is "\Device\HarddiskVolume2"
Ewf Volume Configuration
Volume Size 64512
Segments 0
Segment Size 0
Free segments 0
Max Levels 1
Max Protected Volumes 1
Protected Volumes 1
Ewf Volume percent full -1.#J
Protected volumes
Device Name "\Device\HarddiskVolume1" [C:]


=> C:\WINDOWS\system32>ewfmgr c: (like for /all)
Protected Volume Configuration
Type RAM
State DISABLED
Boot Command NO_CMD
Param1 0
Param2 0
Persistent Data ""
Volume ID D7 FD A2 9A 00 7E 00 00 00 00 00 00 00 00
00 00
Device Name "\Device\HarddiskVolume1" [C:]
Max Levels 1
Clump Size 512
Current Level 1
Memory used for data 0 bytes
Memory used for mapping 0 bytes

I do :

ewfmgr -enable
etprep /all

Result: after reboot

=>C:\WINDOWS\system32>ewfmgr
Unable to find an Ewf volume.

=>C:\WINDOWS\system32>ewfmgr c:
Protected Volume Configuration
Type RAM
State ENABLED
Volume ID D7 FD A2 9A 00 7E 00 00 00 00 00 00 00 00
00 00
Device Name "\Device\HarddiskVolume1" [C:]
Max Levels 1
Clump Size 512
Current Level 1
Memory used for data 2710528 bytes
Memory used for mapping 4096 bytes

ewf don't work correctly but I don't know why ?


regars,
 
According to this, EWF is enabled and working properly.

So this problem is not related to EWF. But then I have no idea what could be
a problem.

Look at:
http://groups.google.com/groups?hl=en&lr=&ie=UTF-8&oe=UTF-8&q="operation+i
nitiated+by+the+registry+failed%22&btnG=Google+Search&meta=group%3Dmicrosoft
..public.windowsxp.embedded.*

Regards,
Slobodan


toto said:
I have 2 hard disc

The first with XP + Target Designer
and I use the second to make xpe ( partition : 600 Mo)

I do like you says but without result Always Isass.exe
error

I do like he says at
http://msdn.microsoft.com/library/default.asp?
url=/library/en-
us/xpehelp/html/xetbshowtocreatecompactflashrun-
timeimage.asp in the "How to Create a Bootable CD-ROM"

When I reboot for the FBA I have only the disc with XPE
and the cd

After the FBA I have :

=>fbalog
15:51:07 - ConfigureEwf() Start.
15:51:07 - Getting EWF config parameters from registry.
15:51:07 - EWF Partition Size = 0 (KBytes), Levels = 1,
Volumes = 1.
15:51:07 - Protected Volume Config #0 :
15:51:07 - Disk= 0,Part= 1,DiskType= IDE,Type= RAM.
15:51:07 - Enable= Disabled, Optimize= 2, LazyWrite=
N.
15:51:07 - Found 1 Hard Disks.
15:51:07 - Searching for El Torito disk.
15:51:07 - Disk0 signature = 0x9AA2FDD7.
15:51:07 - Checking Start value in
System\CurrentControlSet\Services\redbook key.
15:51:07 - Resetting Start value.
15:51:07 - Checking Start value in
System\CurrentControlSet\Services\Imapi key.
15:51:07 - Disk #0 layout info:
15:51:07 - PRIMARY partition,start=0x0000000000007e00,
len=0x0000000025bf9c00, type= 6
15:51:07 - FREE partition,start=0x0000000025c01a00,
len=0x000000092b636800, type= 0
15:51:07 - Allocating EWF in PRIMARY partition,
start=0x0000000025c01a00, len=0x000000000000fc00.
15:51:07 - Created EWF partition on Disk = 0, partition
= 2,size = 0x000000000000fc00 .
15:51:07 - ewfOpen.
15:51:07 - EWF Volume Config on Disk#0, Partition#2:
15:51:07 - Segments = 0, Max Volumes = 1, Max Levels
= 1
15:51:07 - ewfAdd.
15:51:07 - Protected Volume Config on Disk0
\Partition1 :
15:51:07 - Type = RAM, State= DISABLED.
15:51:07 - ewfClose
15:51:07 - Saving EWF configuration to registry:
15:51:07 - Protected Volume ArcName = multi(0)disk(0)
rdisk(0)partition(1).
15:51:07 - ConfigureEwf() End, status = 0x0.
15:51:07 - [CallEntryPointThread] C:\WINDOWS\system32
\ewfdll.dll, ConfigureEwf
15:51:07 - [FBASetProgressText] Resetting Setup Flag...
15:51:10 - [FBADoReboot] Sleeping...
15:51:20 - [FBADoReboot] Rebooting system...
16:16:12 - [FBASetProgressText] Resetting Setup Flag...
16:16:12 - [DoFBA] FBAProcessDLLsInOrder failed!

=> C:\WINDOWS\system32>ewfmgr
The Ewf Volume is "\Device\HarddiskVolume2"
Ewf Volume Configuration
Volume Size 64512
Segments 0
Segment Size 0
Free segments 0
Max Levels 1
Max Protected Volumes 1
Protected Volumes 1
Ewf Volume percent full -1.#J
Protected volumes
Device Name "\Device\HarddiskVolume1" [C:]


=> C:\WINDOWS\system32>ewfmgr c: (like for /all)
Protected Volume Configuration
Type RAM
State DISABLED
Boot Command NO_CMD
Param1 0
Param2 0
Persistent Data ""
Volume ID D7 FD A2 9A 00 7E 00 00 00 00 00 00 00 00
00 00
Device Name "\Device\HarddiskVolume1" [C:]
Max Levels 1
Clump Size 512
Current Level 1
Memory used for data 0 bytes
Memory used for mapping 0 bytes

I do :

ewfmgr -enable
etprep /all

Result: after reboot

=>C:\WINDOWS\system32>ewfmgr
Unable to find an Ewf volume.

=>C:\WINDOWS\system32>ewfmgr c:
Protected Volume Configuration
Type RAM
State ENABLED
Volume ID D7 FD A2 9A 00 7E 00 00 00 00 00 00 00 00
00 00
Device Name "\Device\HarddiskVolume1" [C:]
Max Levels 1
Clump Size 512
Current Level 1
Memory used for data 2710528 bytes
Memory used for mapping 4096 bytes

ewf don't work correctly but I don't know why ?


regars,
Click to expand...
 
re

Configuration : Celeron 2Ghz // 396 Mo DDR

I create a .iso with hd2iso and burn the image with nero
5.5.10 under a cd-rw.

I boot, all is good but at the end error :

=> Windows - Delayed Write Failed
Windows was enable to save the data for the files
c:windows... The data has been lost. This error may be
cause by a failureof your computer hardware or network
connection. Please try to save this file elsewhere.

why ?
 
Sorry, but I have watched the newsgroup that you give me
but
they are nothing for me or I don't see it

I have 396 Mo Ram.
Hard disk 40 Go with only 1 partition of 600 Mo for xpe
and all over is unallocated.
The run time image => 150 Mo.


I don't understand why I haven't enough memory for the
ewf and el torito

Is possible that ewf work but badly configured ?
 
You have more than enough memory.
I said somehow you run out of memory. (this would explain the problem) I
never said that this is actually what is happening.
Is possible that ewf work but badly configured ?
Click to expand...
RAM EWF can't be badly configured, because you don't have options when you
configure it.
It is either working and protecting correct partition, or it is not.
Simple as that. But only thing you need to make sure is that it is actually
enabled and protecting right partition. (This is more like a matter of trust
that if it is working on HDD that it will work on CD, for me it always
worked.).

Regards,
Slobodan
 
hell

when I boot from cdrom
The error message changed, now I hav
1) => Windows Product Activation : A problem is preventing windows from acuuratl
checking the license for this computer. error code 0x8009000

2) => User Environnement : Windows cannot create a tempory profile directory. this may be caused by insufficient security righ

I see on the newsgroup that this probleme is the size of the partition but for me it's a cd-rw

I burn it with a cd-rw , it's good or not
 
El-torito also uses partitions, they are copied from HDD.

So if you were able to pass FBA on your HDD, then this should not be
problem.

If you copy post FBA image to some other disk before you use hd2iso then you
must make sure that FIRST PARTITION size on than new disk matches size of OS
partition when you run FBA.

Regards,
Slobodan



toto said:
hello

when I boot from cdrom
The error message changed, now I have
1) => Windows Product Activation : A problem is preventing windows from acuuratly
checking the license for this computer. error code 0x80090006

2) => User Environnement : Windows cannot create a tempory profile
Click to expand...
directory. this may be caused by insufficient security right
 
I don't understand the question.

Can you give more explanation about the problem.

Regards,
Slobodan
 
You forgot to swap HDD and El-Torito volume letters in your XPe image before
final shutdown.
Or perhaps etprep failed to do this.

You can do this manually if you want from regedit HKLM\System\MountedDevices
I can't give you link that describe this entry since XPe tips page is
currently offline.

You don't need to have HDD present and it should still work. When you make
correct El-Tor.
and my question is : Is it possible ?
Click to expand...

You can use CD for this purpose.

Regards,
Slobodan




toto said:
Sorry for the next message!!

When I boot from the cd "el torito" with the hard disc where is xpe, he boot.
But when I boot with a another Hard disc (XP pro) he can't boot
(error => Can't load user environnement..// Windows Product Activation // isass.exe).

My problem is I want to create a cd for the maintenance which is
Click to expand...
compatible with different Hard Disc to restore the system
 
Back
Top