PAGE_FAULT_IN_NONPAGED_AREA

Has anyone here ever seen this error when simply booting WinPE (disk 1 of
the toolkit)?

The system boots fine, seems to start up all of the services and then about
8 seconds later, crashes with that error.

Can you instruct WinPE to boot using the default VGA Standard driver instead
of it's guess? I've run RAM checks, the ram is fine. Therefore I suspect
that WinPE is assuming an incorrect video driver.


"XPE User" <none@none.com> wrote in message
news:uUOqx0j%23DHA.4088@tk2msftngp13.phx.gbl...
> Has anyone here ever seen this error when simply booting WinPE (disk 1 of
> the toolkit)?
>
> The system boots fine, seems to start up all of the services and then
about
> 8 seconds later, crashes with that error.
>
>

What else do you see on the BSOD? Any info on the driver/app that caused the
crash?
On the same hardware have you tried XP Pro? Have you seen the same problem?

--
KM,
BSquare Corporation

> Has anyone here ever seen this error when simply booting WinPE (disk 1 of
> the toolkit)?
>
> The system boots fine, seems to start up all of the services and then
about
> 8 seconds later, crashes with that error.

What was the stop code?

"XPE User" <none@none.com> wrote in message
news:%23eyUi4j%23DHA.1428@TK2MSFTNGP12.phx.gbl...
> Can you instruct WinPE to boot using the default VGA Standard driver
instead
> of it's guess? I've run RAM checks, the ram is fine. Therefore I suspect
> that WinPE is assuming an incorrect video driver.
>
>
> "XPE User" <none@none.com> wrote in message
> news:uUOqx0j%23DHA.4088@tk2msftngp13.phx.gbl...
> > Has anyone here ever seen this error when simply booting WinPE (disk 1
of
> > the toolkit)?
> >
> > The system boots fine, seems to start up all of the services and then
> about
> > 8 seconds later, crashes with that error.
> >
> >
>
>

The stop code was 0x00000050.

"Doug Hoeffel" <doug.hoeffelNo@SpAmMcamtronics.com> wrote in message
news:%23BP67il%23DHA.3032@TK2MSFTNGP10.phx.gbl...
> What was the stop code?
>
> "XPE User" <none@none.com> wrote in message
> news:%23eyUi4j%23DHA.1428@TK2MSFTNGP12.phx.gbl...
> > Can you instruct WinPE to boot using the default VGA Standard driver
> instead
> > of it's guess? I've run RAM checks, the ram is fine. Therefore I
suspect
> > that WinPE is assuming an incorrect video driver.
> >
> >
> > "XPE User" <none@none.com> wrote in message
> > news:uUOqx0j%23DHA.4088@tk2msftngp13.phx.gbl...
> > > Has anyone here ever seen this error when simply booting WinPE (disk 1
> of
> > > the toolkit)?
> > >
> > > The system boots fine, seems to start up all of the services and then
> > about
> > > 8 seconds later, crashes with that error.
> > >
> > >
> >
> >
>
>

Unfortunately, XP pro also crashes during install. The hardware vendor says
they've installed XP Pro on the hardware before. I'm beginning to think I
have a bum unit.

"KM" <konstmor@nospam.yahoo.com> wrote in message
news:ug291uk%23DHA.1268@TK2MSFTNGP12.phx.gbl...
> What else do you see on the BSOD? Any info on the driver/app that caused
the
> crash?
> On the same hardware have you tried XP Pro? Have you seen the same
problem?
>
> --
> KM,
> BSquare Corporation
>
> > Has anyone here ever seen this error when simply booting WinPE (disk 1
of
> > the toolkit)?
> >
> > The system boots fine, seems to start up all of the services and then
> about
> > 8 seconds later, crashes with that error.
>
>

I've seen this BSOD a few times. Once with mtxdma0.sys so unless you are
using a Matrox frame grabber this is not an issue.

The other time I saw it no file was listed. I thought I had bad memory. A
bad memory stick that is :-). I put in another stick and the machine booted
fine. I put the original memory stick back in and it booted fine so go
figure.

I doubt its related to WinPE especially since your h/w vendor says that XP
Pro loads fine.

HTH... Doug
"XPE User" <none@none.com> wrote in message
news:ufICXMm%23DHA.3500@tk2msftngp13.phx.gbl...
> The stop code was 0x00000050.
>
> "Doug Hoeffel" <doug.hoeffelNo@SpAmMcamtronics.com> wrote in message
> news:%23BP67il%23DHA.3032@TK2MSFTNGP10.phx.gbl...
> > What was the stop code?
> >
> > "XPE User" <none@none.com> wrote in message
> > news:%23eyUi4j%23DHA.1428@TK2MSFTNGP12.phx.gbl...
> > > Can you instruct WinPE to boot using the default VGA Standard driver
> > instead
> > > of it's guess? I've run RAM checks, the ram is fine. Therefore I
> suspect
> > > that WinPE is assuming an incorrect video driver.
> > >
> > >
> > > "XPE User" <none@none.com> wrote in message
> > > news:uUOqx0j%23DHA.4088@tk2msftngp13.phx.gbl...
> > > > Has anyone here ever seen this error when simply booting WinPE (disk
1
> > of
> > > > the toolkit)?
> > > >
> > > > The system boots fine, seems to start up all of the services and
then
> > > about
> > > > 8 seconds later, crashes with that error.
> > > >
> > > >
> > >
> > >
> >
> >
>
>