Help P4t-e Intrusion error????

Intsallling a p4 2.53 ghz in P4t-e motherboard and I'm getthing a hang in
the Bios saying : Message Confirmation-- The system intruded or chassis
tempered with. Check the system?????

I am frozen for awhile in the bios, and only after 3 or 4 restarts I am able
to get into the bios menu to fiddle with settings but it keeps coming back
to this intrusion error.

Is there something in the bios I should turn off or disable ???? I've tried
default setting and I can't escape that error. Thanks. AJ

Well if you install a 533 MHz chip that would be your first problem. The
board was only designed for 400 MHz chip.

"ajb" <aj_brun@hotmail.com> wrote in message
news:9V8Cb.5050$8Y4.233571@read2.cgocable.net...
>
> Intsallling a p4 2.53 ghz in P4t-e motherboard and I'm getthing a hang in
> the Bios saying : Message Confirmation-- The system intruded or chassis
> tempered with. Check the system?????
>
> I am frozen for awhile in the bios, and only after 3 or 4 restarts I am
able
> to get into the bios menu to fiddle with settings but it keeps coming back
> to this intrusion error.
>
> Is there something in the bios I should turn off or disable ???? I've
tried
> default setting and I can't escape that error. Thanks. AJ
>
>
>
>
>
>

In article <if9Cb.664845$6C4.56224@pd7tw1no>, "Dan" <me@nospam.com> wrote:

> Well if you install a 533 MHz chip that would be your first problem. The
> board was only designed for 400 MHz chip.
>
> "ajb" <aj_brun@hotmail.com> wrote in message
> news:9V8Cb.5050$8Y4.233571@read2.cgocable.net...
> >
> > Intsallling a p4 2.53 ghz in P4t-e motherboard and I'm getthing a hang in
> > the Bios saying : Message Confirmation-- The system intruded or chassis
> > tempered with. Check the system?????
> >
> > I am frozen for awhile in the bios, and only after 3 or 4 restarts I am
> able
> > to get into the bios menu to fiddle with settings but it keeps coming back
> > to this intrusion error.
> >
> > Is there something in the bios I should turn off or disable ???? I've
> tried
> > default setting and I can't escape that error. Thanks. AJ
> >

If you look at the picture of the motherboard in the manual (the picture
that identifies all the components and jumpers on the board), there is
a header in the lower right hand corner of the board called "chassis".

In typical Asus style, the header is not documented in that manual. I
looked in the manual for a P4B (my surf machine), and this is what
it shows -

x +5VSB
(no pin)
x chassis_signal
x GND

You are supposed to place a jumper on the two adjacent pins. So, as
long as the chassis_signal is connected to GND, there should be no
complaints from the BIOS. As long as the chassis_signal floats or gets
connected to +5VSB, the BIOS will think your case cover has been opened.

HTH,
Paul

Thanks Paul! I'm back in business running with a 100 FSB--- underclocking a
bit but it moves fast.. I knew this chip would work even with a 533 bus.
"Paul" <nospam@needed.com> wrote in message
news:nospam-1112032257120001@192.168.1.177...
> In article <if9Cb.664845$6C4.56224@pd7tw1no>, "Dan" <me@nospam.com> wrote:
>
> > Well if you install a 533 MHz chip that would be your first problem. The
> > board was only designed for 400 MHz chip.
> >
> > "ajb" <aj_brun@hotmail.com> wrote in message
> > news:9V8Cb.5050$8Y4.233571@read2.cgocable.net...
> > >
> > > Intsallling a p4 2.53 ghz in P4t-e motherboard and I'm getthing a hang
in
> > > the Bios saying : Message Confirmation-- The system intruded or
chassis
> > > tempered with. Check the system?????
> > >
> > > I am frozen for awhile in the bios, and only after 3 or 4 restarts I
am
> > able
> > > to get into the bios menu to fiddle with settings but it keeps coming
back
> > > to this intrusion error.
> > >
> > > Is there something in the bios I should turn off or disable ???? I've
> > tried
> > > default setting and I can't escape that error. Thanks. AJ
> > >
>
> If you look at the picture of the motherboard in the manual (the picture
> that identifies all the components and jumpers on the board), there is
> a header in the lower right hand corner of the board called "chassis".
>
> In typical Asus style, the header is not documented in that manual. I
> looked in the manual for a P4B (my surf machine), and this is what
> it shows -
>
> x +5VSB
> (no pin)
> x chassis_signal
> x GND
>
> You are supposed to place a jumper on the two adjacent pins. So, as
> long as the chassis_signal is connected to GND, there should be no
> complaints from the BIOS. As long as the chassis_signal floats or gets
> connected to +5VSB, the BIOS will think your case cover has been opened.
>
> HTH,
> Paul