I ask this because yesterday have try that particular program to
diagnostic my new new hard drive if it was operating ok.

But eatch time i try to run the test it does nothing...

i have boot from the powermax floppy disk and ran the program twise
but it does nothing.

the hard drve as a primary partition in ntsf format. Maybe that the
problem but on the web site they dont talk about this...

help!

Had this problem several months ago on my A7N8X Deluxe 2.0. I never heard
from Maxtor when I complained...

NOW..., they've posted this little tidbit:

Note: PowerMax v4.06 will not detect Ultra ATA hard disks connected to
motherboards with embedded NVIDIA chipsets (SATA drives are supported). A
new version to address this issue is currently in development and is slated
for release soon. Please check the PowerMax download page periodically for
updates. All versions of PowerMax prior to 4.06 are no longer supported, it
is recommended that you update to version 4.06 before testing your hard
disk.

That nForce2 chipset is full of neat surprises, my favourite is the lack of
PCI IDE Busmaster suppport from DOS.

--
]Robert[ remove "ALLOF YOURCLOTHES" to reply
"DreamMaker" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
>
>
> I ask this because yesterday have try that particular program to
> diagnostic my new new hard drive if it was operating ok.
>
> But eatch time i try to run the test it does nothing...
>
> i have boot from the powermax floppy disk and ran the program twise
> but it does nothing.
>
> the hard drve as a primary partition in ntsf format. Maybe that the
> problem but on the web site they dont talk about this...
>
> help!

On Wed, 31 Dec 2003 13:31:38 -0500, "Robert Sudbury"
<(E-Mail Removed)> wrote:

>Had this problem several months ago on my A7N8X Deluxe 2.0. I never heard
>from Maxtor when I complained...
>
>NOW..., they've posted this little tidbit:
>
>Note: PowerMax v4.06 will not detect Ultra ATA hard disks connected to
>motherboards with embedded NVIDIA chipsets (SATA drives are supported). A
>new version to address this issue is currently in development and is slated
>for release soon. Please check the PowerMax download page periodically for
>updates. All versions of PowerMax prior to 4.06 are no longer supported, it
>is recommended that you update to version 4.06 before testing your hard
>disk.
>
>That nForce2 chipset is full of neat surprises, my favourite is the lack of
>PCI IDE Busmaster suppport from DOS.


After veryfing this issue, i did find out somthing very interesting...

it say,
Procedure for adjusting write verify modes via the WVSET Program

Maxtor hard drives are normally shipped with the "write verify"
feature enabled. The "write verify" feature is enabled to provide
protection against any particles that may have moved caused by
mishandling. This feature is enabled only for the first 10 power
cycles after which the feature will be disabled. A power cycle is the
normal shutdown operations of the computer, including turning the
power off.

"Write Verify" performs a Read of the data just written to the hard
drive and validates the data via the Cyclic Redundancy Check (CRC),
providing additional assurance that the data written to the hard drive
was written correctly. When Write Verify is enabled, the WRITE
performance of the drive is affected as a read occurs for each write.
When disabled WRITE performance is improved as, a read is not
performed for each write.

When performing benchmark operations the "write verify" feature should
be disabled to insure valid comparisons to other products that do not
offer this capability in their product.

To enable, disable, or set occurrence values(number of power on/of
cycles) for the "Write Verify" operation please refer to the WVSET

is the link that verify that.
https://maxtor.custhelp.com/cgi-bin/...dlPTE%2A&p_li=

I found that powermax would bomb if there are any uninstalled drivers. Do
you have any exclamation marks showing in device manager?

"DreamMaker" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
>
>
> I ask this because yesterday have try that particular program to
> diagnostic my new new hard drive if it was operating ok.
>
> But eatch time i try to run the test it does nothing...
>
> i have boot from the powermax floppy disk and ran the program twise
> but it does nothing.
>
> the hard drve as a primary partition in ntsf format. Maybe that the
> problem but on the web site they dont talk about this...
>
> help!

On Wed, 31 Dec 2003 22:28:02 GMT, "tomcas"
<(E-Mail Removed)> wrote:

>I found that powermax would bomb if there are any uninstalled drivers. Do
>you have any exclamation marks showing in device manager?

no, but i've find out that nvidia base motherboard are not support by
the powermax program.

Anyway now i'm shure that my drive is working ok cause now i do get in
data transfers a little more than a maxtor dimondmax plus 9 with 2mb
of buffer.

but i will ask you some thing.
in your bios setting did you let the hardware set your hard drive or
you've instal it with the manual setting.

on the internet they say it suppose to have for the 6y080po

cylinder 158,816 but in my bios it say 39000
precomp it say 39000
head 16 it say 16
sect 63 it say 255
and 80gb it say (when loading 80gb)

what should i do with these setting.

"DreamMaker" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
> On Wed, 31 Dec 2003 22:28:02 GMT, "tomcas"
> <(E-Mail Removed)> wrote:

> in your bios setting did you let the hardware set your hard drive or
> you've instal it with the manual setting.

I always use auto setting in bios- never manual.

>
> on the internet they say it suppose to have for the 6y080po
>
> cylinder 158,816 but in my bios it say 39000
> precomp it say 39000
> head 16 it say 16
> sect 63 it say 255
> and 80gb it say (when loading 80gb)
>
> what should i do with these setting.