PC Review


Reply
Thread Tools Rate Thread

router for 64 bit

 
 
blackburn@connectgradd.net
Guest
Posts: n/a
 
      25th Apr 2009
I just got Broadband internet yesterday. My computer has a built in
wireless LAN a/b/g/n. iI also have a laptop with a builtin LAN. So,
I bought a Netgear wireless router-N. I went to install the CD, and
it only works on a 32 bit processor-Of course, I have a 64 bit
processor. How can I get it to work?? Keep in mind, this is TOTALLY
NEW to me!!!!

Erin
 
Reply With Quote
 
 
 
 
Malke
Guest
Posts: n/a
 
      25th Apr 2009
(E-Mail Removed) wrote:

> I just got Broadband internet yesterday. My computer has a built in
> wireless LAN a/b/g/n. iI also have a laptop with a builtin LAN. So,
> I bought a Netgear wireless router-N. I went to install the CD, and
> it only works on a 32 bit processor-Of course, I have a 64 bit
> processor. How can I get it to work?? Keep in mind, this is TOTALLY
> NEW to me!!!!


You don't need to install anything from the router on your laptop. Configure
the router from either computer using an ethernet cable. General
instructions follow. Note that I wrote them using a Linksys router as an
example so you will need to refer to your Netgear's user manual for the
details such as the default password, etc. Otherwise, the process is not
router brand-dependent.

Setting up a router is quite simple. Normally you run the CD that came with
the router and follow the instructions. If you're running Vista perhaps the
CD that came with the router won't work; I don't know this. But you can set
up the router without a CD. Note that if you have cable Internet, for the
connection you just set the router to do DHCP (or there may even be a
choice of cable for you to select). If you have DSL Internet, you usually
select PPoe and enter the username and password which you chose when
originally setting up the DSL connection. So:

1. Turn off the power to your cable modem.
2. Attach a cat5e ethernet cable (usually provided with the router) going
from the router's Internet/WAN port to the cable modem's ethernet port.
3. Attach a cat5e ethernet cable going from your computer's network adapter
to one of the ports on the router. If you don't have an ethernet cable
(because you were using USB), you will need to go to the store and buy one.
4. Turn on the cable modem. After all the lights are on, turn on the router.

To configure the router:

Have a computer connected to the router with an ethernet cable. Examples
given are for a Linksys router. Refer to your router manual or the router
mftr.'s website for default settings if you don't have a Linksys. Open a
browser such as Internet Explorer or Firefox and in the addressbar type:

http://192.168.1.1 [enter] (this is the router's default IP address, which
varies from router to router so check your manual)

This will bring you to router's login screen. The default username is left
blank and the Linksys default password is "admin" without the quotes. Enter
that information. You are now in the router's configuration utility. Your
configuration utility may differ slightly from mine. The first thing to do
is change the default password because *everyone* knows the default
passwords for various routers.

Click on the Administration link at the top of the page. Enter your new
password. WRITE IT DOWN SOMEWHERE YOU WILL NOT LOSE IT. Re-enter the
password to confirm it and click the Save Settings button at the bottom of
the page. The router will restart and present you with the login box again.
Leave the username blank and put in your new password to get back into the
configuration utility.

Now click on the Wireless link at the top of the page. Change the Wireless
Network Name (SSID) from the default to something you will recognize. I
suggest that my clients not use their family name as the SSID. For example,
you might wish to name your wireless network "CastleAnthrax" or the
like. ;-)

Click the Save Settings and when you get the prompt that your changes were
successful, click on the Wireless Security link which is right next to the
Basic Wireless Settings link (where you changed your SSID). Most computers
purchased within the last 4 years have wireless hardware that will support
WPA2-Personal (also called WPA2-PSK). This is the encryption level you
want. If your wireless hardware is older, use WPA. Do not use WEP as that
is easily cracked within minutes. So go ahead and set the Security Mode to
WPA2-Personal. Do that and enter a passphrase. For example, you might use
the passphrase, "Here be dragons, beware you scurvy dogs!". The passphrase
is what you will enter on any computers that are allowed to connect to the
wireless network. WRITE IT DOWN SOMEWHERE YOU WILL NOT LOSE IT.

At this point, your router is configured and if the computer you were using
to configure the router is normally going to connect wirelessly, disconnect
the ethernet cable and the computer's wireless feature should see your new
network. Enter the passphrase you created (exactly as you wrote it with all
capitalization and punctuation) to join the network and start surfing.

Malke
--
MS-MVP
Elephant Boy Computers - Don't Panic!
http://www.elephantboycomputers.com/#FAQ

 
Reply With Quote
 
 
 
 
DL
Guest
Posts: n/a
 
      26th Apr 2009
You dont have to run any install cd for a Netgear router, installation /
setup instructions are on the netgear site

<(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
>I just got Broadband internet yesterday. My computer has a built in
> wireless LAN a/b/g/n. iI also have a laptop with a builtin LAN. So,
> I bought a Netgear wireless router-N. I went to install the CD, and
> it only works on a 32 bit processor-Of course, I have a 64 bit
> processor. How can I get it to work?? Keep in mind, this is TOTALLY
> NEW to me!!!!
>
> Erin



 
Reply With Quote
 
 
 
Reply

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Home Network - Router behind Router? Can I make Router act as a switch? quentinmacdougall@gmail.com Windows XP Networking 4 29th May 2006 09:56 PM
64 bit - Windows Liberty 64bit, Windows Limited Edition 64 Bit, Microsoft SQL Server 2000 Developer Edition 64 Bit, IBM DB2 64 bit - new ! vvcd AMD 64 Bit 0 17th Sep 2004 09:07 PM
64 bit - Windows Liberty 64bit, Windows Limited Edition 64 Bit, Microsoft SQL Server 2000 Developer Edition 64 Bit, IBM DB2 64 bit - new ! vvcd Processors 0 17th Sep 2004 09:01 PM
Ciber Bit from 0 bit- 128 bit how?? SW Windows XP Internet Explorer 1 30th Apr 2004 02:30 AM
64 bit - Windows Liberty 64bit, Windows Limited Edition 64 Bit, Microsoft SQL Server 2000 Developer Edition 64 Bit - new ! TEL Windows XP General 0 31st Dec 2003 06:58 PM


Features
 

Advertising
 

Newsgroups
 


All times are GMT +1. The time now is 11:20 PM.