Hi, i cant seem to figure some things out about this board and hoped someone
could help me. First i have a serial ata 150 hard drive, not recognised in
the bios, so when i try to put in a secondary ide hard drive it becomes the
master and doesnt load the the OS has gone funny on it, is there any way of
using my SATA HDD as a master the the IDE one so i get can my documents off
it?
Also, is there anyway of turning that RAID thingy off when a load the comp
as it just slows the startup down.

Thanks

"Bishop" <(E-Mail Removed)> wrote in message
news:aJ4ub.1080$(E-Mail Removed)...
> Hi, i cant seem to figure some things out about this board and hoped
someone
> could help me. First i have a serial ata 150 hard drive, not recognised in
> the bios, so when i try to put in a secondary ide hard drive it becomes
the
> master and doesnt load the the OS has gone funny on it, is there any way
of
> using my SATA HDD as a master the the IDE one so i get can my documents
off
> it?
> Also, is there anyway of turning that RAID thingy off when a load the comp
> as it just slows the startup down.
>

I read from this that you want the OS on the sata drive? if so follow this
for winxp, post back if other OS;

1) locate the sata drivers on the cd/web and copy them to a floppy.
2) connect your sata drive, disconnect your ide drive.
3) boot up and enter the bios, change boot order to; CDROM - Floppy - SCSI.
4) boot from winxp cd.
5) very soon after booting from the cd you'll see a message at the bottom
saying 'press F6 to install drivers' or something like that, press F6.
6) wait a while and a screen will come up asking for the driver floppy,
insert it and select the appropriate line, press enter.
7) continue and complete the winxp install.
8) re-boot and it should boot to the new winxp install.
9) shutdown and install your ide drive, re-boot. If your ide drive if
formatted as NTFS you may need to logon as admin and take ownership of your
files to be able to access them.

HTH

--

Ian

A7N8X Deluxe v1.04
Uber Bios 1006 + Sata Bios
XP2500 @ 2400MHz
Corsair Twinx1024-3200LLPT
200 x 12.0
ATI Radeon 9700Pro
2 x Maxtor 120GB 8MB SATA RAID 0

No that's not it, i have my OS installed on my sata drive (exactly like u
said! Was tough) but i want to get some files off my IDE disk drive by using
the SATA drive's OS.

Thanks!

"IanDunbar" <(E-Mail Removed)> wrote in message
news:bpamar$1mjj08$(E-Mail Removed)...
>
> "Bishop" <(E-Mail Removed)> wrote in message
> news:aJ4ub.1080$(E-Mail Removed)...
> > Hi, i cant seem to figure some things out about this board and hoped
> someone
> > could help me. First i have a serial ata 150 hard drive, not recognised
in
> > the bios, so when i try to put in a secondary ide hard drive it becomes
> the
> > master and doesnt load the the OS has gone funny on it, is there any way
> of
> > using my SATA HDD as a master the the IDE one so i get can my documents
> off
> > it?
> > Also, is there anyway of turning that RAID thingy off when a load the
comp
> > as it just slows the startup down.
> >
>
> I read from this that you want the OS on the sata drive? if so follow this
> for winxp, post back if other OS;
>
> 1) locate the sata drivers on the cd/web and copy them to a floppy.
> 2) connect your sata drive, disconnect your ide drive.
> 3) boot up and enter the bios, change boot order to; CDROM - Floppy -
SCSI.
> 4) boot from winxp cd.
> 5) very soon after booting from the cd you'll see a message at the bottom
> saying 'press F6 to install drivers' or something like that, press F6.
> 6) wait a while and a screen will come up asking for the driver floppy,
> insert it and select the appropriate line, press enter.
> 7) continue and complete the winxp install.
> 8) re-boot and it should boot to the new winxp install.
> 9) shutdown and install your ide drive, re-boot. If your ide drive if
> formatted as NTFS you may need to logon as admin and take ownership of
your
> files to be able to access them.
>
> HTH
>
> --
>
> Ian
>
> A7N8X Deluxe v1.04
> Uber Bios 1006 + Sata Bios
> XP2500 @ 2400MHz
> Corsair Twinx1024-3200LLPT
> 200 x 12.0
> ATI Radeon 9700Pro
> 2 x Maxtor 120GB 8MB SATA RAID 0
>
>

"Bishop" <(E-Mail Removed)> wrote in message
news:975ub.1094$(E-Mail Removed)...
> No that's not it, i have my OS installed on my sata drive (exactly like u
> said! Was tough) but i want to get some files off my IDE disk drive by
using
> the SATA drive's OS.

Right, have you got it booting from the sata drive with the ide drive
installed? if not is it because the ide drive boots when you connect it up,
if so then change boot order in the bios to; CDROM - Floppy - SCSI, the bios
decides that sata drives are SCSI and if you have HD0 before SCSI it will
boot the ide drive. (hope that makes sense?)

If your ide drive is formatted as NTFS you may need to logon as admin and
take ownership of your
files to be able to access them.

Am I getting any closer?


--

Ian

A7N8X Deluxe v1.04
Uber Bios 1006 + Sata Bios
XP2500 @ 2310MHz
Corsair Twinx1024-3200LLPT
210 x 11.0
ATI Radeon 9700Pro
2 x Maxtor 120GB 8MB SATA RAID 0

It's ok, i got that figured now, i put the 1st boot device as SCSI.

Thanks!

"Bishop" <(E-Mail Removed)> wrote in message
news:975ub.1094$(E-Mail Removed)...
> No that's not it, i have my OS installed on my sata drive (exactly like u
> said! Was tough) but i want to get some files off my IDE disk drive by
using
> the SATA drive's OS.
>
> Thanks!
>
> "IanDunbar" <(E-Mail Removed)> wrote in message
> news:bpamar$1mjj08$(E-Mail Removed)...
> >
> > "Bishop" <(E-Mail Removed)> wrote in message
> > news:aJ4ub.1080$(E-Mail Removed)...
> > > Hi, i cant seem to figure some things out about this board and hoped
> > someone
> > > could help me. First i have a serial ata 150 hard drive, not
recognised
> in
> > > the bios, so when i try to put in a secondary ide hard drive it
becomes
> > the
> > > master and doesnt load the the OS has gone funny on it, is there any
way
> > of
> > > using my SATA HDD as a master the the IDE one so i get can my
documents
> > off
> > > it?
> > > Also, is there anyway of turning that RAID thingy off when a load the
> comp
> > > as it just slows the startup down.
> > >
> >
> > I read from this that you want the OS on the sata drive? if so follow
this
> > for winxp, post back if other OS;
> >
> > 1) locate the sata drivers on the cd/web and copy them to a floppy.
> > 2) connect your sata drive, disconnect your ide drive.
> > 3) boot up and enter the bios, change boot order to; CDROM - Floppy -
> SCSI.
> > 4) boot from winxp cd.
> > 5) very soon after booting from the cd you'll see a message at the
bottom
> > saying 'press F6 to install drivers' or something like that, press F6.
> > 6) wait a while and a screen will come up asking for the driver floppy,
> > insert it and select the appropriate line, press enter.
> > 7) continue and complete the winxp install.
> > 8) re-boot and it should boot to the new winxp install.
> > 9) shutdown and install your ide drive, re-boot. If your ide drive if
> > formatted as NTFS you may need to logon as admin and take ownership of
> your
> > files to be able to access them.
> >
> > HTH
> >
> > --
> >
> > Ian
> >
> > A7N8X Deluxe v1.04
> > Uber Bios 1006 + Sata Bios
> > XP2500 @ 2400MHz
> > Corsair Twinx1024-3200LLPT
> > 200 x 12.0
> > ATI Radeon 9700Pro
> > 2 x Maxtor 120GB 8MB SATA RAID 0
> >
> >
>
>