LEXMARK X 85 printer

Window home XP
Service Pack 2 installed

Trying to reload my printer software will not recognize
my printer.

Here is the message I receive,

16 Bit windows subsystem

C: windows\system32\auto exec.nt

The system file is not suitable for running MS-DOS and
Microsoft windows applications
Choose and close to terminate this application.

*The programs almost installs but near the end where it
ask to connect you USB cable the screen goes into a mode
where the hour glass and the icon just blinks off and on.

It shows the following

Software for your new hardware (scanner and printer this
process may take up to two minutes.
To begin connect USB cable to you computer and printer

This is as far as it goes before going into the blinking
mode as stated above *

When I abort the program I then get another error block
which states,

INST monitor
Failed add monitor
( ) -3006

Any ideas on what's happening or better yet can anyone
help?

Thank you

Have you downloaded the latest drivers from Lexmark yet?
>-----Original Message-----
>LEXMARK X 85 printer
>
>Window home XP
>Service Pack 2 installed
>
>Trying to reload my printer software will not recognize
>my printer.
>
>Here is the message I receive,
>
>16 Bit windows subsystem
>
>C: windows\system32\auto exec.nt
>
>The system file is not suitable for running MS-DOS and
>Microsoft windows applications
>Choose and close to terminate this application.
>
>*The programs almost installs but near the end where it
>ask to connect you USB cable the screen goes into a mode
>where the hour glass and the icon just blinks off and on.
>
>It shows the following
>
>Software for your new hardware (scanner and printer this
>process may take up to two minutes.
>To begin connect USB cable to you computer and printer
>
>This is as far as it goes before going into the blinking
>mode as stated above *
>
>When I abort the program I then get another error block
>which states,
>
>INST monitor
>Failed add monitor
>( ) -3006
>
>Any ideas on what's happening or better yet can anyone
>help?
>
>Thank you
>
>.
>

Yes I tryed that out yesterday with your advice. No luck
same problem. Micrsoft Service Pack 2 may have caused
the problem. This all started when I loaded the service
pack 2

>-----Original Message-----
>Have you downloaded the latest drivers from Lexmark yet?
>>-----Original Message-----
>>LEXMARK X 85 printer
>>
>>Window home XP
>>Service Pack 2 installed
>>
>>Trying to reload my printer software will not recognize
>>my printer.
>>
>>Here is the message I receive,
>>
>>16 Bit windows subsystem
>>
>>C: windows\system32\auto exec.nt
>>
>>The system file is not suitable for running MS-DOS and
>>Microsoft windows applications
>>Choose and close to terminate this application.
>>
>>*The programs almost installs but near the end where it
>>ask to connect you USB cable the screen goes into a
mode
>>where the hour glass and the icon just blinks off and
on.
>>
>>It shows the following
>>
>>Software for your new hardware (scanner and printer
this
>>process may take up to two minutes.
>>To begin connect USB cable to you computer and printer
>>
>>This is as far as it goes before going into the
blinking
>>mode as stated above *
>>
>>When I abort the program I then get another error
block
>>which states,
>>
>>INST monitor
>>Failed add monitor
>>( ) -3006
>>
>>Any ideas on what's happening or better yet can anyone
>>help?
>>
>>Thank you
>>
>>.
>>
>.
>

Try the site below and follow the link to Lexmark drivers
http://members.shaw.ca/bsanders/Clea...Drivers.htm#Le
xmarkDriver
It has been of benefit to other in the past.
Best of Luck
>-----Original Message-----
>Yes I tryed that out yesterday with your advice. No
luck
>same problem. Micrsoft Service Pack 2 may have caused
>the problem. This all started when I loaded the service
>pack 2
>
>>-----Original Message-----
>>Have you downloaded the latest drivers from Lexmark yet?
>>>-----Original Message-----
>>>LEXMARK X 85 printer
>>>
>>>Window home XP
>>>Service Pack 2 installed
>>>
>>>Trying to reload my printer software will not
recognize
>>>my printer.
>>>
>>>Here is the message I receive,
>>>
>>>16 Bit windows subsystem
>>>
>>>C: windows\system32\auto exec.nt
>>>
>>>The system file is not suitable for running MS-DOS and
>>>Microsoft windows applications
>>>Choose and close to terminate this application.
>>>
>>>*The programs almost installs but near the end where
it
>>>ask to connect you USB cable the screen goes into a
>mode
>>>where the hour glass and the icon just blinks off and
>on.
>>>
>>>It shows the following
>>>
>>>Software for your new hardware (scanner and printer
>this
>>>process may take up to two minutes.
>>>To begin connect USB cable to you computer and printer
>>>
>>>This is as far as it goes before going into the
>blinking
>>>mode as stated above *
>>>
>>>When I abort the program I then get another error
>block
>>>which states,
>>>
>>>INST monitor
>>>Failed add monitor
>>>( ) -3006
>>>
>>>Any ideas on what's happening or better yet can anyone
>>>help?
>>>
>>>Thank you
>>>
>>>.
>>>
>>.
>>
>.
>