PC Review


Reply
Thread Tools Rate Thread

Can't get answers from ASUS

 
 
sherwindu
Guest
Posts: n/a
 
      10th May 2005
I phoned Asus to get information on how to replace the AMD 761 System Controller Fan on my A7M266
motherboard. Left a message, but they never called me back. Sent an email to tech support and got
the brush off, telling me to
go back to my vendor for support. I'll never buy another Asus board.

Sherwin D.

 
Reply With Quote
 
 
 
 
Hawkeye
Guest
Posts: n/a
 
      10th May 2005
If your refering to the northbridge chipset fan remove it and install
one of these

http://www.zalman.co.kr/eng/product/...dx=71&code=014

http://www.newegg.com/Product/Produc...82E16835118214


--
ASUS A8V/Athlon 64 FX-55
ATI RADEON X800XT PE
1GB OCZ Gold Edition Rev3 DDR PC-3700
 
Reply With Quote
 
Egil Solberg
Guest
Posts: n/a
 
      10th May 2005
sherwindu wrote:
> I phoned Asus to get information on how to replace the AMD 761 System
> Controller Fan on my A7M266 motherboard. Left a message, but they
> never called me back. Sent an email to tech support and got the
> brush off, telling me to
> go back to my vendor for support. I'll never buy another Asus board.


Just remove the fan. The fan stopped working after I had done some vacuuming
inside a friendīs case.
Removed it, but of course kept the heatsink. The PC works fine without it.
It was an AMD 761 NB.


 
Reply With Quote
 
sherwindu
Guest
Posts: n/a
 
      19th May 2005
I got my replacement fan from newegg. It was larger than I imagined from the internet picture and came
with no mounting hardware. I decided to try and take off
the ARX fan, which had stopped running. After removing two phillips screws, the fan and connecting
cable came out of a black case enclosure. There were two thumb screw on this case, which after turning
did not seem to release it. I don't know what is holding the fan case to the board. Also, I can't
imagine how this cooling was supposed to work, since behind the fan was a solid piece of plastic.
Maybe this plastic was kept cool, and it inturn kept the chips cool. I'm sorry I bought an ASUS
board! Trying to find information about this fan from ARX is almost impossible. Their site is in
Chinese, and even after loading the plug in to
Adobe for this language set, it could not be read. Emails to the US office of ARX
have produced no result. How can ASUS put an unsupportable component on their
board? I refuse to rip out this board to send it to the RMA department of ASUS,
just to replace a stupid fan. This is just another instance of sending all our production
overseas. Anyone know of a good Chinese language school?

Sherwin D.

sherwindu wrote:

> I phoned Asus to get information on how to replace the AMD 761 System Controller Fan on my A7M266
> motherboard. Left a message, but they never called me back. Sent an email to tech support and got
> the brush off, telling me to
> go back to my vendor for support. I'll never buy another Asus board.
>
> Sherwin D.


 
Reply With Quote
 
Mark A
Guest
Posts: n/a
 
      19th May 2005
"sherwindu" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
>I got my replacement fan from newegg. It was larger than I imagined from
>the internet picture and came
> with no mounting hardware. I decided to try and take off
> the ARX fan, which had stopped running. After removing two phillips
> screws, the fan and connecting
> cable came out of a black case enclosure. There were two thumb screw on
> this case, which after turning
> did not seem to release it. I don't know what is holding the fan case to
> the board. Also, I can't
> imagine how this cooling was supposed to work, since behind the fan was a
> solid piece of plastic.
> Maybe this plastic was kept cool, and it inturn kept the chips cool. I'm
> sorry I bought an ASUS
> board! Trying to find information about this fan from ARX is almost
> impossible. Their site is in
> Chinese, and even after loading the plug in to
> Adobe for this language set, it could not be read. Emails to the US
> office of ARX
> have produced no result. How can ASUS put an unsupportable component on
> their
> board? I refuse to rip out this board to send it to the RMA department of
> ASUS,
> just to replace a stupid fan. This is just another instance of sending
> all our production
> overseas. Anyone know of a good Chinese language school?
>
> Sherwin D.


You refer to fan case? Are you talking about the heatsink for the chipset?

There is a HSF (heatsink/fan) for the chipset. If the fan went out, did they
send you a completely new HSF or just the fan?

To replace most chipset HSF's you need to get at the bottom of the
motherboard. If just the fan is being replaced, then maybe you can do it
from the top.

There are lots of aftermarket HSF's for chipsets that usually work better
than the OEM and that are passively cooled or have much quieter fans. Check
with the vendor websites to see which ones are compatible. I would also
seriously suggest you get an experienced person (friend, neighbor) to help
you figure this out, because it is almost impossible to understand the exact
situation based on your description.


 
Reply With Quote
 
sherwindu
Guest
Posts: n/a
 
      19th May 2005


Mark A wrote:

> "sherwindu" <(E-Mail Removed)> wrote in message
> news:(E-Mail Removed)...
> >I got my replacement fan from newegg. It was larger than I imagined from
> >the internet picture and came
> > with no mounting hardware. I decided to try and take off
> > the ARX fan, which had stopped running. After removing two phillips
> > screws, the fan and connecting
> > cable came out of a black case enclosure. There were two thumb screw on
> > this case, which after turning
> > did not seem to release it. I don't know what is holding the fan case to
> > the board. Also, I can't
> > imagine how this cooling was supposed to work, since behind the fan was a
> > solid piece of plastic.
> > Maybe this plastic was kept cool, and it inturn kept the chips cool. I'm
> > sorry I bought an ASUS
> > board! Trying to find information about this fan from ARX is almost
> > impossible. Their site is in
> > Chinese, and even after loading the plug in to
> > Adobe for this language set, it could not be read. Emails to the US
> > office of ARX
> > have produced no result. How can ASUS put an unsupportable component on
> > their
> > board? I refuse to rip out this board to send it to the RMA department of
> > ASUS,
> > just to replace a stupid fan. This is just another instance of sending
> > all our production
> > overseas. Anyone know of a good Chinese language school?
> >
> > Sherwin D.

>
> You refer to fan case? Are you talking about the heatsink for the chipset?
>
> There is a HSF (heatsink/fan) for the chipset. If the fan went out, did they
> send you a completely new HSF or just the fan?
>
> To replace most chipset HSF's you need to get at the bottom of the
> motherboard. If just the fan is being replaced, then maybe you can do it
> from the top.
>
> There are lots of aftermarket HSF's for chipsets that usually work better
> than the OEM and that are passively cooled or have much quieter fans. Check
> with the vendor websites to see which ones are compatible. I would also
> seriously suggest you get an experienced person (friend, neighbor) to help
> you figure this out, because it is almost impossible to understand the exact
> situation based on your description.


I think with a B.S. in engineering, I should be able to handle this myself.

Again, what came off the board was just a thin fan with a wire attached.
This fan matches up exactly with a corresponding plastic housing which is
still attached to the motherboard. There were two thumbscrews on it, but
releasing them did not allow me to remove this plastic housing. I doubt
very much that this housing is the chipset itself, unless it is behind the plastic
where I can't see it. I have a replacement fan ready to mount, if I can only
figure out how to remove this plastic fan housing. ARX, who makes the
original fan is less than helpfull in providing any specs on it. Their website
doesn't have any information, and their agent doesn't reply to my email.

Sherwin D.


 
Reply With Quote
 
Mark A
Guest
Posts: n/a
 
      19th May 2005
"sherwindu" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
> I think with a B.S. in engineering, I should be able to handle this
> myself.
>
> Again, what came off the board was just a thin fan with a wire attached.
> This fan matches up exactly with a corresponding plastic housing which
> is
> still attached to the motherboard. There were two thumbscrews on it,
> but
> releasing them did not allow me to remove this plastic housing. I doubt
> very much that this housing is the chipset itself, unless it is behind
> the plastic
> where I can't see it. I have a replacement fan ready to mount, if I can
> only
> figure out how to remove this plastic fan housing. ARX, who makes the
> original fan is less than helpfull in providing any specs on it. Their
> website
> doesn't have any information, and their agent doesn't reply to my email.
>
> Sherwin D.
>

I didn't say the housing was the chipset itself. I asked whether the housing
was the heatsink (not clear in your post). Usually, there is a heatsink that
sits on top of the chip, and a fan that blows on the heatsink (to dissipate
heat faster). But not being able to see your motherboard (or pics of it), I
don't know for sure. You didn't mention anything about a heatsink in your
post.

As I mentioned, there are several companies that make good HS's (passive) or
HSF's (with fan) for chipsets, and are much better at cooling, and much
quieter than the OEM ones.


 
Reply With Quote
 
sherwindu
Guest
Posts: n/a
 
      20th May 2005


Mark A wrote:

> "sherwindu" <(E-Mail Removed)> wrote in message
> news:(E-Mail Removed)...
> > I think with a B.S. in engineering, I should be able to handle this
> > myself.
> >
> > Again, what came off the board was just a thin fan with a wire attached.
> > This fan matches up exactly with a corresponding plastic housing which
> > is
> > still attached to the motherboard. There were two thumbscrews on it,
> > but
> > releasing them did not allow me to remove this plastic housing. I doubt
> > very much that this housing is the chipset itself, unless it is behind
> > the plastic
> > where I can't see it. I have a replacement fan ready to mount, if I can
> > only
> > figure out how to remove this plastic fan housing. ARX, who makes the
> > original fan is less than helpfull in providing any specs on it. Their
> > website
> > doesn't have any information, and their agent doesn't reply to my email.
> >
> > Sherwin D.
> >

> I didn't say the housing was the chipset itself. I asked whether the housing
> was the heatsink (not clear in your post).


I know what a heatsink looks like. This housing is about an eigth of an inch high
of black plastic which appears to rest on the surface of the mother board. There
is no heat sink anywhere, in view.

> Usually, there is a heatsink that
> sits on top of the chip, and a fan that blows on the heatsink (to dissipate
> heat faster). But not being able to see your motherboard (or pics of it), I
> don't know for sure. You didn't mention anything about a heatsink in your
> post.
>
> As I mentioned, there are several companies that make good HS's (passive) or
> HSF's (with fan) for chipsets, and are much better at cooling, and much
> quieter than the OEM ones.


I have a substitute fan read to go. Problem is I don't know how to remove the
plastic housing to replace it with the new fan. I have been avoiding taking off the
motherboard from the case, so that I can get a look at whats on the opposite side.
If there is a chipset under this plastic housing, it has to be a very low profile one.
It also makes me wonder what kind of cooling this fan can do, if the chipset is
covered with a solid plastic housing.

Sherwin D.


 
Reply With Quote
 
Bill
Guest
Posts: n/a
 
      20th May 2005
In article <(E-Mail Removed)>, (E-Mail Removed)
says...
>
>

<snip>

There's a fair chance it's stuck on with thermal tape.

Bill
 
Reply With Quote
 
Jeff
Guest
Posts: n/a
 
      20th May 2005
You just said "the fan in question goes over item 2" but from the image and
your reference to the 761 system controller that would location 1. Anyway I
had to replace one of those on my Asus board (not the same model). Anyway
mine was held on by a couple of i guess closest term would plungers that
expanded on the back side of the board. I had to get behind to squeeze that
together and push thru from the back side. I will add that of course with
the kind of luck I have the new fan which was same size voltage excetera the
hole still would not line back up correctly, so hopefully you have better
luck in that regards.

Just my thoughts.

Jeff

"sherwindu" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
> I am trying to post a 'jpg' image from my manual, and the fan in question
> goes over item #2.
>
> Sherwin D.
>
> Mark A wrote:
>
> > "sherwindu" <(E-Mail Removed)> wrote in message
> > news:(E-Mail Removed)...
> > > I think with a B.S. in engineering, I should be able to handle this
> > > myself.
> > >
> > > Again, what came off the board was just a thin fan with a wire

attached.
> > > This fan matches up exactly with a corresponding plastic housing

which
> > > is
> > > still attached to the motherboard. There were two thumbscrews on

it,
> > > but
> > > releasing them did not allow me to remove this plastic housing. I

doubt
> > > very much that this housing is the chipset itself, unless it is

behind
> > > the plastic
> > > where I can't see it. I have a replacement fan ready to mount, if I

can
> > > only
> > > figure out how to remove this plastic fan housing. ARX, who makes

the
> > > original fan is less than helpfull in providing any specs on it.

Their
> > > website
> > > doesn't have any information, and their agent doesn't reply to my

email.
> > >
> > > Sherwin D.
> > >

> > I didn't say the housing was the chipset itself. I asked whether the

housing
> > was the heatsink (not clear in your post). Usually, there is a heatsink

that
> > sits on top of the chip, and a fan that blows on the heatsink (to

dissipate
> > heat faster). But not being able to see your motherboard (or pics of

it), I
> > don't know for sure. You didn't mention anything about a heatsink in

your
> > post.
> >
> > As I mentioned, there are several companies that make good HS's

(passive) or
> > HSF's (with fan) for chipsets, and are much better at cooling, and much
> > quieter than the OEM ones.

>



----------------------------------------------------------------------------
----





 
Reply With Quote
 
 
 
Reply

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Re: asus mb and asus video card..asus or ati drivers? Bert Hyman ATI Video Cards 0 29th Dec 2010 03:17 PM
Answers to questions i have posted, re email answers gandian Windows XP Security 9 9th Mar 2008 10:34 PM
Re: Can't get answers from ASUS rstlne Asus Motherboards 5 14th May 2005 06:47 AM
Creating a test, need to compare answers to correct answers =?Utf-8?B?amVmZg==?= Microsoft Frontpage 1 16th Nov 2004 06:09 AM
ASUS BIOS pops up and says, CPU FREQ or something that effect. ASUS ASUS MOBO Jelly Asus Motherboards 2 21st Feb 2004 12:36 AM


Features
 

Advertising
 

Newsgroups
 


All times are GMT +1. The time now is 02:55 PM.