PC Review


Reply
Thread Tools Rate Thread

Who can help me. Chipset fan on A8N-SLI Deluxe

 
 
Figo
Guest
Posts: n/a
 
      12th Nov 2005
Could You tell me how to change the original chipset fun. I'd prefer to
install passive cooling system.
What kind? How efficient it wolud be?
Thx


 
Reply With Quote
 
 
 
 
milleron
Guest
Posts: n/a
 
      13th Nov 2005
On Sat, 12 Nov 2005 10:42:35 +0100, "Figo" <(E-Mail Removed)> wrote:

>Could You tell me how to change the original chipset fun. I'd prefer to
>install passive cooling system.
>What kind? How efficient it wolud be?
>Thx
>

You have to unscrew the current fan and pop it off the chipset.
Most users opt for the Zalman product. I think its part # is NB47J.
You clean any thermal paste on the chipset and install the Zalman
heatsink per its included instructions. How efficient it is will
depend on how much air you get blowing on it, but it should be plenty
efficient enough to cool the chipset as well as the original little
fan does.

Ron
 
Reply With Quote
 
Figo
Guest
Posts: n/a
 
      13th Nov 2005
Is it possible to check chipset temperature. Is it difficult to unscrew FUN.
Does it void my warranty.


 
Reply With Quote
 
DDC
Guest
Posts: n/a
 
      13th Nov 2005
On Sat, 12 Nov 2005 10:42:35 +0100, "Figo" <(E-Mail Removed)> wrote:

>Could You tell me how to change the original chipset fun. I'd prefer to
>install passive cooling system.
>What kind? How efficient it wolud be?
>Thx
>



the chipset fan are generally fix with two clip that can be remove.
you could try the MCX159-CU series Chipset Heat sinks for AMD® &
Intel® platform motherboards without the fan that way it would be
totally silence...
 
Reply With Quote
 
DDC
Guest
Posts: n/a
 
      13th Nov 2005
On Sun, 13 Nov 2005 04:22:03 GMT, milleron
<(E-Mail Removed)> wrote:

>On Sat, 12 Nov 2005 10:42:35 +0100, "Figo" <(E-Mail Removed)> wrote:
>
>>Could You tell me how to change the original chipset fun. I'd prefer to
>>install passive cooling system.
>>What kind? How efficient it wolud be?
>>Thx
>>

>You have to unscrew the current fan and pop it off the chipset.
>Most users opt for the Zalman product. I think its part # is NB47J.
>You clean any thermal paste on the chipset and install the Zalman
>heatsink per its included instructions. How efficient it is will
>depend on how much air you get blowing on it, but it should be plenty
>efficient enough to cool the chipset as well as the original little
>fan does.
>
>Ron


Hi Ron, Could you tell me what the purpuse of get a better cooling of
the chipset.?
 
Reply With Quote
 
milleron
Guest
Posts: n/a
 
      14th Nov 2005
On Sun, 13 Nov 2005 15:46:48 -0500, DDC <(E-Mail Removed)> wrote:

>On Sun, 13 Nov 2005 04:22:03 GMT, milleron
><(E-Mail Removed)> wrote:
>
>>On Sat, 12 Nov 2005 10:42:35 +0100, "Figo" <(E-Mail Removed)> wrote:
>>
>>>Could You tell me how to change the original chipset fun. I'd prefer to
>>>install passive cooling system.
>>>What kind? How efficient it wolud be?
>>>Thx
>>>

>>You have to unscrew the current fan and pop it off the chipset.
>>Most users opt for the Zalman product. I think its part # is NB47J.
>>You clean any thermal paste on the chipset and install the Zalman
>>heatsink per its included instructions. How efficient it is will
>>depend on how much air you get blowing on it, but it should be plenty
>>efficient enough to cool the chipset as well as the original little
>>fan does.
>>
>>Ron

>
>Hi Ron, Could you tell me what the purpuse of get a better cooling of
>the chipset.?


Overheating of the chipset will lead to decreased life span, and, more
importantly, can lead to instability of the system.

Ron
 
Reply With Quote
 
Larry
Guest
Posts: n/a
 
      14th Nov 2005
I used the Zalman NB47J to replace the stock HSF.
You will have to remove your motherboard if it is installed
in a case. Otherwise it is simple to replace. See the link
below to see how I did mine.

http://www.larryewing.com/chipset.htm
K5ZH

"Figo" <(E-Mail Removed)> wrote in message
news:dl4dkm$42j$(E-Mail Removed)...
> Could You tell me how to change the original chipset fun. I'd prefer to
> install passive cooling system.
> What kind? How efficient it wolud be?
> Thx
>



 
Reply With Quote
 
Viđarr
Guest
Posts: n/a
 
      15th Nov 2005

"Figo" <(E-Mail Removed)> wrote in message
news:dl4dkm$42j$(E-Mail Removed)...
> Could You tell me how to change the original chipset fun. I'd prefer to
> install passive cooling system.
> What kind? How efficient it wolud be?
> Thx
>



I went through the original A8N-SLI Deluxe chipset fan quickly (within a
couple weeks of getting my computer). I wasn't at all thrilled with the
idea of having to remove the mainboard to install the Asus replacement (I
have neither space nor tools here), so I came up with an alternate plan.

My solution was to completely remove the stock fan, leaving the heatsink in
place and mounted to the chipset. Removing the stock fan is easy. (The
only problem is that the enclosure is held on by four very small screws, and
the fan held in place by three even
smaller ones. Because they can easily lose themselves among the other
components if dropped, a magnetic screwdriver makes the whole process much
easier. Finding lost ones and storing them safely outside the computer
easily adds an hour to the procedure, but not doing so risks disaster.)

I then replaced it with a Sunon maglev fan (40mm x 10mm, 3-wire) using four
#4 x 3/4
inch (2.74mm x 19mm) wood/metal screws (NOT machine screws), securing the
screws between the vanes of the heatsink to seat the fan. In order to have
adequate clearance and visibility, I needed to pull the SLI “bridge” and the
top videocard (I have two XFX 6800 Ultras in SLI mode) and then reinstall
the card and the bridge after I’d installed the fan, but that was the only
other problem I had.

The Sunon fan seems to run faster than I'd like (~13,000 RPM), but I don't
know if that's its true speed or if it actually is running at 6,500 RPM.
It's
very quiet. (I haven't figured out how to adjust the fan multiplier, if
that's even possible. I bought five of the fans while I was at it, so I'm
covered even if it is at the extreme high end of its range.) Everything
seems to be working fine so far.

The advantage to this fix is that:

[1] it doesn't involve removing the mainboard;

[2] it's technically and mechanically easy;

[3] takes about an hour if all goes as planned;

[4] the 10mm-thick Sunon fan mounted on the existing heatsink
provides adequate clearance, even for the twin XFXs.

There may be better solutions, but I know this one works.

When I eventually upgrade from this machine, and if I have the luxury of
time, I'm going to wait until more mainboards are available and have track
records, and then choose the best. I don't want to go through THIS sort of
problem again. I mean if *I* could come up with an inexpensive, workable
solution, why couldn't Asus do it before they put the board into production?
According to the reviews, the A8N-SLI Deluxe (when *I* bought mine) was the
best board available. (There was no mention of the chipset fan problem in
any of the reviews I read.) I'd have gladly paid a bit more to not have had
the Northbridge chipset fan problem in the first place. This is not the way
for Asus to win friends.


Viđarr




 
Reply With Quote
 
Natéag
Guest
Posts: n/a
 
      15th Nov 2005
The a8n-sli Premium
answers all your wishes.

"Viđarr" <(E-Mail Removed)> a écrit dans le message de
news: Srcef.468$(E-Mail Removed)...
>
> "Figo" <(E-Mail Removed)> wrote in message
> news:dl4dkm$42j$(E-Mail Removed)...
>> Could You tell me how to change the original chipset fun. I'd prefer to
>> install passive cooling system.
>> What kind? How efficient it wolud be?
>> Thx
>>

>
>
> I went through the original A8N-SLI Deluxe chipset fan quickly (within a
> couple weeks of getting my computer). I wasn't at all thrilled with the
> idea of having to remove the mainboard to install the Asus replacement (I
> have neither space nor tools here), so I came up with an alternate plan.
>
> My solution was to completely remove the stock fan, leaving the heatsink
> in place and mounted to the chipset. Removing the stock fan is easy.
> (The only problem is that the enclosure is held on by four very small
> screws, and the fan held in place by three even
> smaller ones. Because they can easily lose themselves among the other
> components if dropped, a magnetic screwdriver makes the whole process much
> easier. Finding lost ones and storing them safely outside the computer
> easily adds an hour to the procedure, but not doing so risks disaster.)
>
> I then replaced it with a Sunon maglev fan (40mm x 10mm, 3-wire) using
> four #4 x 3/4
> inch (2.74mm x 19mm) wood/metal screws (NOT machine screws), securing the
> screws between the vanes of the heatsink to seat the fan. In order to
> have
> adequate clearance and visibility, I needed to pull the SLI "bridge" and
> the top videocard (I have two XFX 6800 Ultras in SLI mode) and then
> reinstall the card and the bridge after I'd installed the fan, but that
> was the only other problem I had.
>
> The Sunon fan seems to run faster than I'd like (~13,000 RPM), but I don't
> know if that's its true speed or if it actually is running at 6,500 RPM.
> It's
> very quiet. (I haven't figured out how to adjust the fan multiplier, if
> that's even possible. I bought five of the fans while I was at it, so I'm
> covered even if it is at the extreme high end of its range.) Everything
> seems to be working fine so far.
>
> The advantage to this fix is that:
>
> [1] it doesn't involve removing the mainboard;
>
> [2] it's technically and mechanically easy;
>
> [3] takes about an hour if all goes as planned;
>
> [4] the 10mm-thick Sunon fan mounted on the existing heatsink
> provides adequate clearance, even for the twin XFXs.
>
> There may be better solutions, but I know this one works.
>
> When I eventually upgrade from this machine, and if I have the luxury of
> time, I'm going to wait until more mainboards are available and have track
> records, and then choose the best. I don't want to go through THIS sort
> of
> problem again. I mean if *I* could come up with an inexpensive, workable
> solution, why couldn't Asus do it before they put the board into
> production?
> According to the reviews, the A8N-SLI Deluxe (when *I* bought mine) was
> the
> best board available. (There was no mention of the chipset fan problem in
> any of the reviews I read.) I'd have gladly paid a bit more to not have
> had
> the Northbridge chipset fan problem in the first place. This is not the
> way for Asus to win friends.
>
>
> Viđarr
>
>
>
>



 
Reply With Quote
 
milleron
Guest
Posts: n/a
 
      16th Nov 2005
On Mon, 14 Nov 2005 23:13:58 -0500, "Natéag" <(E-Mail Removed)>
wrote:

>The a8n-sli Premium
>answers all your wishes.


Perhaps. I was very impressed with how cool my chipset was when I
first built the computer in June. Now, a few months later, it's too
hot to touch comfortably, and I'm having instability problems that are
proving terribly difficult to troubleshoot. I'm not yet positive it's
not an overheated nForce chipset.
>
>"Viđarr" <(E-Mail Removed)> a écrit dans le message de
>news: Srcef.468$(E-Mail Removed)...
>>
>> "Figo" <(E-Mail Removed)> wrote in message
>> news:dl4dkm$42j$(E-Mail Removed)...
>>> Could You tell me how to change the original chipset fun. I'd prefer to
>>> install passive cooling system.
>>> What kind? How efficient it wolud be?
>>> Thx
>>>

>>
>>
>> I went through the original A8N-SLI Deluxe chipset fan quickly (within a
>> couple weeks of getting my computer). I wasn't at all thrilled with the
>> idea of having to remove the mainboard to install the Asus replacement (I
>> have neither space nor tools here), so I came up with an alternate plan.
>>
>> My solution was to completely remove the stock fan, leaving the heatsink
>> in place and mounted to the chipset. Removing the stock fan is easy.
>> (The only problem is that the enclosure is held on by four very small
>> screws, and the fan held in place by three even
>> smaller ones. Because they can easily lose themselves among the other
>> components if dropped, a magnetic screwdriver makes the whole process much
>> easier. Finding lost ones and storing them safely outside the computer
>> easily adds an hour to the procedure, but not doing so risks disaster.)
>>
>> I then replaced it with a Sunon maglev fan (40mm x 10mm, 3-wire) using
>> four #4 x 3/4
>> inch (2.74mm x 19mm) wood/metal screws (NOT machine screws), securing the
>> screws between the vanes of the heatsink to seat the fan. In order to
>> have
>> adequate clearance and visibility, I needed to pull the SLI "bridge" and
>> the top videocard (I have two XFX 6800 Ultras in SLI mode) and then
>> reinstall the card and the bridge after I'd installed the fan, but that
>> was the only other problem I had.
>>
>> The Sunon fan seems to run faster than I'd like (~13,000 RPM), but I don't
>> know if that's its true speed or if it actually is running at 6,500 RPM.
>> It's
>> very quiet. (I haven't figured out how to adjust the fan multiplier, if
>> that's even possible. I bought five of the fans while I was at it, so I'm
>> covered even if it is at the extreme high end of its range.) Everything
>> seems to be working fine so far.
>>
>> The advantage to this fix is that:
>>
>> [1] it doesn't involve removing the mainboard;
>>
>> [2] it's technically and mechanically easy;
>>
>> [3] takes about an hour if all goes as planned;
>>
>> [4] the 10mm-thick Sunon fan mounted on the existing heatsink
>> provides adequate clearance, even for the twin XFXs.
>>
>> There may be better solutions, but I know this one works.
>>
>> When I eventually upgrade from this machine, and if I have the luxury of
>> time, I'm going to wait until more mainboards are available and have track
>> records, and then choose the best. I don't want to go through THIS sort
>> of
>> problem again. I mean if *I* could come up with an inexpensive, workable
>> solution, why couldn't Asus do it before they put the board into
>> production?
>> According to the reviews, the A8N-SLI Deluxe (when *I* bought mine) was
>> the
>> best board available. (There was no mention of the chipset fan problem in
>> any of the reviews I read.) I'd have gladly paid a bit more to not have
>> had
>> the Northbridge chipset fan problem in the first place. This is not the
>> way for Asus to win friends.
>>
>>
>> Viđarr
>>
>>
>>
>>

>


Ron
 
Reply With Quote
 
 
 
Reply

Thread Tools
Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
A8N-SLI Deluxe New Chipset Fan! edde Asus Motherboards 12 19th Sep 2005 07:07 AM
A8N-SLI Deluxe chipset fan failure Freedom55 Asus Motherboards 8 25th Aug 2005 01:19 AM
- Looking for replacement A8N-SLI Deluxe chipset fan... recommendations? Richard Hayden Asus Motherboards 14 5th Jun 2005 01:25 AM
P4P 800 Deluxe - which Controller Chipset to use for SATA??/ cvj Asus Motherboards 1 31st Dec 2003 11:04 PM
P4P800 Deluxe chipset heatsink Navid Asus Motherboards 7 9th Nov 2003 03:44 AM


Features
 

Advertising
 

Newsgroups
 


All times are GMT +1. The time now is 08:36 PM.