I have the following 56 k modem micronet Shuttle 3000 ( SP3008U) connected
with XP SP2 and an ISDN phone line in greece,
with the caller ID enabled and working on the line.

I am using the latest XP drivers from the micronet site.

http://www.micronet.info/Products/56K/SP3008UA.asp

I have looked at the manual and on the site, but I cannot find out if the
modem supports caller ID and how to enable it on Windows XP.

I have tried using the extra command: AT#CID=1

Does anyone have any idea?

TIA

Kenny

The data from QUERRY is:

ATQ0V1E0 - OK
AT+GMM - +GMM: HCF V.90 56K Data,Fax,Voice USB Modem
AT+FCLASS=? - 0,1,1.0,8
AT#CLS=? - COMMAND NOT SUPPORTED
AT+GCI? - +GCI: FE
AT+GCI=? - +GCI:
(20,26,50,53,54,00,61,6C,73,7E,89,9C,FE,A9,B5,16,09,8C,BC,27,35,85,87,88,B7,BB,8E,36,B8,B4)
ATI1 - 255
ATI2 - OK
ATI3 - 9.5.2.172.036
ATI4 - Conexant HCF V.92 56K Data,Fax,Voice USB Modem
ATI5 - 254
ATI6 - DP Rev P8773
V92 SPX RAM Ver 30
V92 CTL RAM Ver 30
K56FLEX SPX RAM Ver 47
K56FLEX CTL RAM Ver 47
ATI7 - 255

Kenny,

1st: Please do not cross post.

2nd, please try http://www.modemsite.com/56k/rockv92.asp and see if it
solves your problem.

From the above site, use the init strings:

+PSS=0;+PCW=0;+PQC=0
or
+PSS=0;+PCW=0;+PQC=0;+PMH=0

--
Jabez Gan
Give me a chance, Let me help you!
http://www.blizhosting.com


"Kenny S" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
>I have the following 56 k modem micronet Shuttle 3000 ( SP3008U) connected
>with XP SP2 and an ISDN phone line in greece,
> with the caller ID enabled and working on the line.
>
> I am using the latest XP drivers from the micronet site.
>
> http://www.micronet.info/Products/56K/SP3008UA.asp
>
> I have looked at the manual and on the site, but I cannot find out if the
> modem supports caller ID and how to enable it on Windows XP.
>
> I have tried using the extra command: AT#CID=1
>
> Does anyone have any idea?
>
> TIA
>
> Kenny
>
> The data from QUERRY is:
>
> ATQ0V1E0 - OK
> AT+GMM - +GMM: HCF V.90 56K Data,Fax,Voice USB Modem
> AT+FCLASS=? - 0,1,1.0,8
> AT#CLS=? - COMMAND NOT SUPPORTED
> AT+GCI? - +GCI: FE
> AT+GCI=? - +GCI:
> (20,26,50,53,54,00,61,6C,73,7E,89,9C,FE,A9,B5,16,09,8C,BC,27,35,85,87,88,B7,BB,8E,36,B8,B4)
> ATI1 - 255
> ATI2 - OK
> ATI3 - 9.5.2.172.036
> ATI4 - Conexant HCF V.92 56K Data,Fax,Voice USB Modem
> ATI5 - 254
> ATI6 - DP Rev P8773
> V92 SPX RAM Ver 30
> V92 CTL RAM Ver 30
> K56FLEX SPX RAM Ver 47
> K56FLEX CTL RAM Ver 47
> ATI7 - 255
>
>
>

Hello,

I was contacted by the Micronet support and I was told that infact this
modem does not have caller ID function.

However I have another modem , diamond supraexpress 56 e PRO,
and I am using the default drivers XPSP2 installed.

Does anyone know if this modem has a caller ID function?
The Diamond site does not have this info, and I do not have the manual.

Thanks in advance...

Kenny



"Jabez Gan" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
> Kenny,
>
> 1st: Please do not cross post.
>
> 2nd, please try http://www.modemsite.com/56k/rockv92.asp and see if it
> solves your problem.
>
> From the above site, use the init strings:
>
> +PSS=0;+PCW=0;+PQC=0
> or
> +PSS=0;+PCW=0;+PQC=0;+PMH=0
>
> --
> Jabez Gan
> Give me a chance, Let me help you!
> http://www.blizhosting.com
>
>
> "Kenny S" <(E-Mail Removed)> wrote in message
> news:(E-Mail Removed)...
>>I have the following 56 k modem micronet Shuttle 3000 ( SP3008U) connected
>>with XP SP2 and an ISDN phone line in greece,
>> with the caller ID enabled and working on the line.
>>
>> I am using the latest XP drivers from the micronet site.
>>
>> http://www.micronet.info/Products/56K/SP3008UA.asp
>>
>> I have looked at the manual and on the site, but I cannot find out if the
>> modem supports caller ID and how to enable it on Windows XP.
>>
>> I have tried using the extra command: AT#CID=1
>>
>> Does anyone have any idea?
>>
>> TIA
>>
>> Kenny
>>
>> The data from QUERRY is:
>>
>> ATQ0V1E0 - OK
>> AT+GMM - +GMM: HCF V.90 56K Data,Fax,Voice USB Modem
>> AT+FCLASS=? - 0,1,1.0,8
>> AT#CLS=? - COMMAND NOT SUPPORTED
>> AT+GCI? - +GCI: FE
>> AT+GCI=? - +GCI:
>> (20,26,50,53,54,00,61,6C,73,7E,89,9C,FE,A9,B5,16,09,8C,BC,27,35,85,87,88,B7,BB,8E,36,B8,B4)
>> ATI1 - 255
>> ATI2 - OK
>> ATI3 - 9.5.2.172.036
>> ATI4 - Conexant HCF V.92 56K Data,Fax,Voice USB Modem
>> ATI5 - 254
>> ATI6 - DP Rev P8773
>> V92 SPX RAM Ver 30
>> V92 CTL RAM Ver 30
>> K56FLEX SPX RAM Ver 47
>> K56FLEX CTL RAM Ver 47
>> ATI7 - 255
>>
>>
>>
>
>

It does not.

--
Jonah
"Kenny S" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
> Hello,
>
> I was contacted by the Micronet support and I was told that infact this
> modem does not have caller ID function.
>
> However I have another modem , diamond supraexpress 56 e PRO,
> and I am using the default drivers XPSP2 installed.
>
> Does anyone know if this modem has a caller ID function?
> The Diamond site does not have this info, and I do not have the manual.
>
> Thanks in advance...
>
> Kenny
>
>
>
> "Jabez Gan" <(E-Mail Removed)> wrote in message
> news:(E-Mail Removed)...
>> Kenny,
>>
>> 1st: Please do not cross post.
>>
>> 2nd, please try http://www.modemsite.com/56k/rockv92.asp and see if it
>> solves your problem.
>>
>> From the above site, use the init strings:
>>
>> +PSS=0;+PCW=0;+PQC=0
>> or
>> +PSS=0;+PCW=0;+PQC=0;+PMH=0
>>
>> --
>> Jabez Gan
>> Give me a chance, Let me help you!
>> http://www.blizhosting.com
>>
>>
>> "Kenny S" <(E-Mail Removed)> wrote in message
>> news:(E-Mail Removed)...
>>>I have the following 56 k modem micronet Shuttle 3000 ( SP3008U)
>>>connected with XP SP2 and an ISDN phone line in greece,
>>> with the caller ID enabled and working on the line.
>>>
>>> I am using the latest XP drivers from the micronet site.
>>>
>>> http://www.micronet.info/Products/56K/SP3008UA.asp
>>>
>>> I have looked at the manual and on the site, but I cannot find out if
>>> the modem supports caller ID and how to enable it on Windows XP.
>>>
>>> I have tried using the extra command: AT#CID=1
>>>
>>> Does anyone have any idea?
>>>
>>> TIA
>>>
>>> Kenny
>>>
>>> The data from QUERRY is:
>>>
>>> ATQ0V1E0 - OK
>>> AT+GMM - +GMM: HCF V.90 56K Data,Fax,Voice USB Modem
>>> AT+FCLASS=? - 0,1,1.0,8
>>> AT#CLS=? - COMMAND NOT SUPPORTED
>>> AT+GCI? - +GCI: FE
>>> AT+GCI=? - +GCI:
>>> (20,26,50,53,54,00,61,6C,73,7E,89,9C,FE,A9,B5,16,09,8C,BC,27,35,85,87,88,B7,BB,8E,36,B8,B4)
>>> ATI1 - 255
>>> ATI2 - OK
>>> ATI3 - 9.5.2.172.036
>>> ATI4 - Conexant HCF V.92 56K Data,Fax,Voice USB Modem
>>> ATI5 - 254
>>> ATI6 - DP Rev P8773
>>> V92 SPX RAM Ver 30
>>> V92 CTL RAM Ver 30
>>> K56FLEX SPX RAM Ver 47
>>> K56FLEX CTL RAM Ver 47
>>> ATI7 - 255
>>>
>>>
>>>
>>
>>
>
>

Hi sleepless

can you tell me how you know/got this information?

thank you


"Sleepless in Seattle" <(E-Mail Removed)> wrote in message
news:sub_d.10529$(E-Mail Removed)...
> It does not.
>
> --
> Jonah
> "Kenny S" <(E-Mail Removed)> wrote in message
> news:(E-Mail Removed)...
>> Hello,
>>
>> I was contacted by the Micronet support and I was told that infact this
>> modem does not have caller ID function.
>>
>> However I have another modem , diamond supraexpress 56 e PRO,
>> and I am using the default drivers XPSP2 installed.
>>
>> Does anyone know if this modem has a caller ID function?
>> The Diamond site does not have this info, and I do not have the manual.
>>
>> Thanks in advance...
>>
>> Kenny
>>
>>
>>
>> "Jabez Gan" <(E-Mail Removed)> wrote in message
>> news:(E-Mail Removed)...
>>> Kenny,
>>>
>>> 1st: Please do not cross post.
>>>
>>> 2nd, please try http://www.modemsite.com/56k/rockv92.asp and see if it
>>> solves your problem.
>>>
>>> From the above site, use the init strings:
>>>
>>> +PSS=0;+PCW=0;+PQC=0
>>> or
>>> +PSS=0;+PCW=0;+PQC=0;+PMH=0
>>>
>>> --
>>> Jabez Gan
>>> Give me a chance, Let me help you!
>>> http://www.blizhosting.com
>>>
>>>
>>> "Kenny S" <(E-Mail Removed)> wrote in message
>>> news:(E-Mail Removed)...
>>>>I have the following 56 k modem micronet Shuttle 3000 ( SP3008U)
>>>>connected with XP SP2 and an ISDN phone line in greece,
>>>> with the caller ID enabled and working on the line.
>>>>
>>>> I am using the latest XP drivers from the micronet site.
>>>>
>>>> http://www.micronet.info/Products/56K/SP3008UA.asp
>>>>
>>>> I have looked at the manual and on the site, but I cannot find out if
>>>> the modem supports caller ID and how to enable it on Windows XP.
>>>>
>>>> I have tried using the extra command: AT#CID=1
>>>>
>>>> Does anyone have any idea?
>>>>
>>>> TIA
>>>>
>>>> Kenny
>>>>
>>>> The data from QUERRY is:
>>>>
>>>> ATQ0V1E0 - OK
>>>> AT+GMM - +GMM: HCF V.90 56K Data,Fax,Voice USB Modem
>>>> AT+FCLASS=? - 0,1,1.0,8
>>>> AT#CLS=? - COMMAND NOT SUPPORTED
>>>> AT+GCI? - +GCI: FE
>>>> AT+GCI=? - +GCI:
>>>> (20,26,50,53,54,00,61,6C,73,7E,89,9C,FE,A9,B5,16,09,8C,BC,27,35,85,87,88,B7,BB,8E,36,B8,B4)
>>>> ATI1 - 255
>>>> ATI2 - OK
>>>> ATI3 - 9.5.2.172.036
>>>> ATI4 - Conexant HCF V.92 56K Data,Fax,Voice USB Modem
>>>> ATI5 - 254
>>>> ATI6 - DP Rev P8773
>>>> V92 SPX RAM Ver 30
>>>> V92 CTL RAM Ver 30
>>>> K56FLEX SPX RAM Ver 47
>>>> K56FLEX CTL RAM Ver 47
>>>> ATI7 - 255
>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>
>

On Thu, 17 Mar 2005 10:12:25 +0200
Kenny S croaked the following in
microsoft.public.windowsxp.help_and_support...

> The Diamond site does not have this info, and I do not have the manual.
>

The manual is downloadable from here,
http://www.micronet.com.tw/download/...6K/sp3008u.pdf
--
Regards
frogman http://www.frogman.org.uk for free downloads and more...

If you think you're not confused, you're just not thinking too clearly

If a company does not specifically state that a piece of hardware can do
something - it probably can't. I guess I am naive. I tend to believe
published specs, until I find out otherwise.

--
Regards,

Richard Urban

aka Crusty (-: Old B@stard :-)

If you knew as much as you think you know,
You would realize that you don't know what you thought you knew!


"Kenny S" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
> Hello,
>
> I was contacted by the Micronet support and I was told that infact this
> modem does not have caller ID function.
>
> However I have another modem , diamond supraexpress 56 e PRO,
> and I am using the default drivers XPSP2 installed.
>
> Does anyone know if this modem has a caller ID function?
> The Diamond site does not have this info, and I do not have the manual.
>
> Thanks in advance...
>
> Kenny
>
>
>
> "Jabez Gan" <(E-Mail Removed)> wrote in message
> news:(E-Mail Removed)...
>> Kenny,
>>
>> 1st: Please do not cross post.
>>
>> 2nd, please try http://www.modemsite.com/56k/rockv92.asp and see if it
>> solves your problem.
>>
>> From the above site, use the init strings:
>>
>> +PSS=0;+PCW=0;+PQC=0
>> or
>> +PSS=0;+PCW=0;+PQC=0;+PMH=0
>>
>> --
>> Jabez Gan
>> Give me a chance, Let me help you!
>> http://www.blizhosting.com
>>
>>
>> "Kenny S" <(E-Mail Removed)> wrote in message
>> news:(E-Mail Removed)...
>>>I have the following 56 k modem micronet Shuttle 3000 ( SP3008U)
>>>connected with XP SP2 and an ISDN phone line in greece,
>>> with the caller ID enabled and working on the line.
>>>
>>> I am using the latest XP drivers from the micronet site.
>>>
>>> http://www.micronet.info/Products/56K/SP3008UA.asp
>>>
>>> I have looked at the manual and on the site, but I cannot find out if
>>> the modem supports caller ID and how to enable it on Windows XP.
>>>
>>> I have tried using the extra command: AT#CID=1
>>>
>>> Does anyone have any idea?
>>>
>>> TIA
>>>
>>> Kenny
>>>
>>> The data from QUERRY is:
>>>
>>> ATQ0V1E0 - OK
>>> AT+GMM - +GMM: HCF V.90 56K Data,Fax,Voice USB Modem
>>> AT+FCLASS=? - 0,1,1.0,8
>>> AT#CLS=? - COMMAND NOT SUPPORTED
>>> AT+GCI? - +GCI: FE
>>> AT+GCI=? - +GCI:
>>> (20,26,50,53,54,00,61,6C,73,7E,89,9C,FE,A9,B5,16,09,8C,BC,27,35,85,87,88,B7,BB,8E,36,B8,B4)
>>> ATI1 - 255
>>> ATI2 - OK
>>> ATI3 - 9.5.2.172.036
>>> ATI4 - Conexant HCF V.92 56K Data,Fax,Voice USB Modem
>>> ATI5 - 254
>>> ATI6 - DP Rev P8773
>>> V92 SPX RAM Ver 30
>>> V92 CTL RAM Ver 30
>>> K56FLEX SPX RAM Ver 47
>>> K56FLEX CTL RAM Ver 47
>>> ATI7 - 255
>>>
>>>
>>>
>>
>>
>
>

> If a company does not specifically state that a piece of hardware can do
> something - it probably can't

Yes thats what I am starting to find out too.....

I have now connected my 3rd dial up modem, a zoom 3049L....
but that does not seem to work either....

PS: I have DSL for the internet, I just want the caller ID function and fax.

Kenny

Kenny

"Richard Urban" <(E-Mail Removed)> wrote in message
news:%(E-Mail Removed)...
> If a company does not specifically state that a piece of hardware can do
> something - it probably can't. I guess I am naive. I tend to believe
> published specs, until I find out otherwise.
>
> --
> Regards,
>
> Richard Urban
>
> aka Crusty (-: Old B@stard :-)
>
> If you knew as much as you think you know,
> You would realize that you don't know what you thought you knew!
>
>
> "Kenny S" <(E-Mail Removed)> wrote in message
> news:(E-Mail Removed)...
>> Hello,
>>
>> I was contacted by the Micronet support and I was told that infact this
>> modem does not have caller ID function.
>>
>> However I have another modem , diamond supraexpress 56 e PRO,
>> and I am using the default drivers XPSP2 installed.
>>
>> Does anyone know if this modem has a caller ID function?
>> The Diamond site does not have this info, and I do not have the manual.
>>
>> Thanks in advance...
>>
>> Kenny
>>
>>
>>
>> "Jabez Gan" <(E-Mail Removed)> wrote in message
>> news:(E-Mail Removed)...
>>> Kenny,
>>>
>>> 1st: Please do not cross post.
>>>
>>> 2nd, please try http://www.modemsite.com/56k/rockv92.asp and see if it
>>> solves your problem.
>>>
>>> From the above site, use the init strings:
>>>
>>> +PSS=0;+PCW=0;+PQC=0
>>> or
>>> +PSS=0;+PCW=0;+PQC=0;+PMH=0
>>>
>>> --
>>> Jabez Gan
>>> Give me a chance, Let me help you!
>>> http://www.blizhosting.com
>>>
>>>
>>> "Kenny S" <(E-Mail Removed)> wrote in message
>>> news:(E-Mail Removed)...
>>>>I have the following 56 k modem micronet Shuttle 3000 ( SP3008U)
>>>>connected with XP SP2 and an ISDN phone line in greece,
>>>> with the caller ID enabled and working on the line.
>>>>
>>>> I am using the latest XP drivers from the micronet site.
>>>>
>>>> http://www.micronet.info/Products/56K/SP3008UA.asp
>>>>
>>>> I have looked at the manual and on the site, but I cannot find out if
>>>> the modem supports caller ID and how to enable it on Windows XP.
>>>>
>>>> I have tried using the extra command: AT#CID=1
>>>>
>>>> Does anyone have any idea?
>>>>
>>>> TIA
>>>>
>>>> Kenny
>>>>
>>>> The data from QUERRY is:
>>>>
>>>> ATQ0V1E0 - OK
>>>> AT+GMM - +GMM: HCF V.90 56K Data,Fax,Voice USB Modem
>>>> AT+FCLASS=? - 0,1,1.0,8
>>>> AT#CLS=? - COMMAND NOT SUPPORTED
>>>> AT+GCI? - +GCI: FE
>>>> AT+GCI=? - +GCI:
>>>> (20,26,50,53,54,00,61,6C,73,7E,89,9C,FE,A9,B5,16,09,8C,BC,27,35,85,87,88,B7,BB,8E,36,B8,B4)
>>>> ATI1 - 255
>>>> ATI2 - OK
>>>> ATI3 - 9.5.2.172.036
>>>> ATI4 - Conexant HCF V.92 56K Data,Fax,Voice USB Modem
>>>> ATI5 - 254
>>>> ATI6 - DP Rev P8773
>>>> V92 SPX RAM Ver 30
>>>> V92 CTL RAM Ver 30
>>>> K56FLEX SPX RAM Ver 47
>>>> K56FLEX CTL RAM Ver 47
>>>> ATI7 - 255
>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>
>

Zoom 3049L does include caller ID. please see
http://www.zoom.com/documentation/dial_up/VenusCRM.pdf page 62.

Hope this helps.

--
Jabez Gan
Give me a chance, Let me help you!
http://www.blizhosting.com


"Kenny S" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
>> If a company does not specifically state that a piece of hardware can do
>> something - it probably can't
>
> Yes thats what I am starting to find out too.....
>
> I have now connected my 3rd dial up modem, a zoom 3049L....
> but that does not seem to work either....
>
> PS: I have DSL for the internet, I just want the caller ID function and
> fax.
>
> Kenny
>
> Kenny
>
> "Richard Urban" <(E-Mail Removed)> wrote in message
> news:%(E-Mail Removed)...
>> If a company does not specifically state that a piece of hardware can do
>> something - it probably can't. I guess I am naive. I tend to believe
>> published specs, until I find out otherwise.
>>
>> --
>> Regards,
>>
>> Richard Urban
>>
>> aka Crusty (-: Old B@stard :-)
>>
>> If you knew as much as you think you know,
>> You would realize that you don't know what you thought you knew!
>>
>>
>> "Kenny S" <(E-Mail Removed)> wrote in message
>> news:(E-Mail Removed)...
>>> Hello,
>>>
>>> I was contacted by the Micronet support and I was told that infact this
>>> modem does not have caller ID function.
>>>
>>> However I have another modem , diamond supraexpress 56 e PRO,
>>> and I am using the default drivers XPSP2 installed.
>>>
>>> Does anyone know if this modem has a caller ID function?
>>> The Diamond site does not have this info, and I do not have the manual.
>>>
>>> Thanks in advance...
>>>
>>> Kenny
>>>
>>>
>>>
>>> "Jabez Gan" <(E-Mail Removed)> wrote in message
>>> news:(E-Mail Removed)...
>>>> Kenny,
>>>>
>>>> 1st: Please do not cross post.
>>>>
>>>> 2nd, please try http://www.modemsite.com/56k/rockv92.asp and see if it
>>>> solves your problem.
>>>>
>>>> From the above site, use the init strings:
>>>>
>>>> +PSS=0;+PCW=0;+PQC=0
>>>> or
>>>> +PSS=0;+PCW=0;+PQC=0;+PMH=0
>>>>
>>>> --
>>>> Jabez Gan
>>>> Give me a chance, Let me help you!
>>>> http://www.blizhosting.com
>>>>
>>>>
>>>> "Kenny S" <(E-Mail Removed)> wrote in message
>>>> news:(E-Mail Removed)...
>>>>>I have the following 56 k modem micronet Shuttle 3000 ( SP3008U)
>>>>>connected with XP SP2 and an ISDN phone line in greece,
>>>>> with the caller ID enabled and working on the line.
>>>>>
>>>>> I am using the latest XP drivers from the micronet site.
>>>>>
>>>>> http://www.micronet.info/Products/56K/SP3008UA.asp
>>>>>
>>>>> I have looked at the manual and on the site, but I cannot find out if
>>>>> the modem supports caller ID and how to enable it on Windows XP.
>>>>>
>>>>> I have tried using the extra command: AT#CID=1
>>>>>
>>>>> Does anyone have any idea?
>>>>>
>>>>> TIA
>>>>>
>>>>> Kenny
>>>>>
>>>>> The data from QUERRY is:
>>>>>
>>>>> ATQ0V1E0 - OK
>>>>> AT+GMM - +GMM: HCF V.90 56K Data,Fax,Voice USB Modem
>>>>> AT+FCLASS=? - 0,1,1.0,8
>>>>> AT#CLS=? - COMMAND NOT SUPPORTED
>>>>> AT+GCI? - +GCI: FE
>>>>> AT+GCI=? - +GCI:
>>>>> (20,26,50,53,54,00,61,6C,73,7E,89,9C,FE,A9,B5,16,09,8C,BC,27,35,85,87,88,B7,BB,8E,36,B8,B4)
>>>>> ATI1 - 255
>>>>> ATI2 - OK
>>>>> ATI3 - 9.5.2.172.036
>>>>> ATI4 - Conexant HCF V.92 56K Data,Fax,Voice USB Modem
>>>>> ATI5 - 254
>>>>> ATI6 - DP Rev P8773
>>>>> V92 SPX RAM Ver 30
>>>>> V92 CTL RAM Ver 30
>>>>> K56FLEX SPX RAM Ver 47
>>>>> K56FLEX CTL RAM Ver 47
>>>>> ATI7 - 255
>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>
>

I am posting this for googlegrousp referance....

I got a reply from ZOOM support and as it seems it only partially supports
caller ID under only some situations (that your isp has v.92 and you are in
netwaiting modem on hold), here is there reply:

Subject
Caller ID on the serial external modem 3049L

Discussion Thread
Response (GARY)03/17/2005 09:05 AM
Hello

Thank you for the opportunity to be of service.

Caller ID is supported when you are on line connected to a V.92 compliant
server, using the NetWaiting modem-on-hold application.

See - Title: Modem on Hold Caller ID is not working
URL:
http://zoom.custhelp.com/cgi-bin/zoo...ted=1031252456


Hope this helps.

Gary


Kenny





"Jabez Gan" <(E-Mail Removed)> wrote in message
news:O8$(E-Mail Removed)...
> Zoom 3049L does include caller ID. please see
> http://www.zoom.com/documentation/dial_up/VenusCRM.pdf page 62.
>
> Hope this helps.
>
> --
> Jabez Gan
> Give me a chance, Let me help you!
> http://www.blizhosting.com
>
>
> "Kenny S" <(E-Mail Removed)> wrote in message
> news:(E-Mail Removed)...
>>> If a company does not specifically state that a piece of hardware can do
>>> something - it probably can't
>>
>> Yes thats what I am starting to find out too.....
>>
>> I have now connected my 3rd dial up modem, a zoom 3049L....
>> but that does not seem to work either....
>>
>> PS: I have DSL for the internet, I just want the caller ID function and
>> fax.
>>
>> Kenny
>>
>> Kenny
>>
>> "Richard Urban" <(E-Mail Removed)> wrote in message
>> news:%(E-Mail Removed)...
>>> If a company does not specifically state that a piece of hardware can do
>>> something - it probably can't. I guess I am naive. I tend to believe
>>> published specs, until I find out otherwise.
>>>
>>> --
>>> Regards,
>>>
>>> Richard Urban
>>>
>>> aka Crusty (-: Old B@stard :-)
>>>
>>> If you knew as much as you think you know,
>>> You would realize that you don't know what you thought you knew!
>>>
>>>
>>> "Kenny S" <(E-Mail Removed)> wrote in message
>>> news:(E-Mail Removed)...
>>>> Hello,
>>>>
>>>> I was contacted by the Micronet support and I was told that infact this
>>>> modem does not have caller ID function.
>>>>
>>>> However I have another modem , diamond supraexpress 56 e PRO,
>>>> and I am using the default drivers XPSP2 installed.
>>>>
>>>> Does anyone know if this modem has a caller ID function?
>>>> The Diamond site does not have this info, and I do not have the manual.
>>>>
>>>> Thanks in advance...
>>>>
>>>> Kenny
>>>>
>>>>
>>>>
>>>> "Jabez Gan" <(E-Mail Removed)> wrote in message
>>>> news:(E-Mail Removed)...
>>>>> Kenny,
>>>>>
>>>>> 1st: Please do not cross post.
>>>>>
>>>>> 2nd, please try http://www.modemsite.com/56k/rockv92.asp and see if it
>>>>> solves your problem.
>>>>>
>>>>> From the above site, use the init strings:
>>>>>
>>>>> +PSS=0;+PCW=0;+PQC=0
>>>>> or
>>>>> +PSS=0;+PCW=0;+PQC=0;+PMH=0
>>>>>
>>>>> --
>>>>> Jabez Gan
>>>>> Give me a chance, Let me help you!
>>>>> http://www.blizhosting.com
>>>>>
>>>>>
>>>>> "Kenny S" <(E-Mail Removed)> wrote in message
>>>>> news:(E-Mail Removed)...
>>>>>>I have the following 56 k modem micronet Shuttle 3000 ( SP3008U)
>>>>>>connected with XP SP2 and an ISDN phone line in greece,
>>>>>> with the caller ID enabled and working on the line.
>>>>>>
>>>>>> I am using the latest XP drivers from the micronet site.
>>>>>>
>>>>>> http://www.micronet.info/Products/56K/SP3008UA.asp
>>>>>>
>>>>>> I have looked at the manual and on the site, but I cannot find out if
>>>>>> the modem supports caller ID and how to enable it on Windows XP.
>>>>>>
>>>>>> I have tried using the extra command: AT#CID=1
>>>>>>
>>>>>> Does anyone have any idea?
>>>>>>
>>>>>> TIA
>>>>>>
>>>>>> Kenny
>>>>>>
>>>>>> The data from QUERRY is:
>>>>>>
>>>>>> ATQ0V1E0 - OK
>>>>>> AT+GMM - +GMM: HCF V.90 56K Data,Fax,Voice USB Modem
>>>>>> AT+FCLASS=? - 0,1,1.0,8
>>>>>> AT#CLS=? - COMMAND NOT SUPPORTED
>>>>>> AT+GCI? - +GCI: FE
>>>>>> AT+GCI=? - +GCI:
>>>>>> (20,26,50,53,54,00,61,6C,73,7E,89,9C,FE,A9,B5,16,09,8C,BC,27,35,85,87,88,B7,BB,8E,36,B8,B4)
>>>>>> ATI1 - 255
>>>>>> ATI2 - OK
>>>>>> ATI3 - 9.5.2.172.036
>>>>>> ATI4 - Conexant HCF V.92 56K Data,Fax,Voice USB Modem
>>>>>> ATI5 - 254
>>>>>> ATI6 - DP Rev P8773
>>>>>> V92 SPX RAM Ver 30
>>>>>> V92 CTL RAM Ver 30
>>>>>> K56FLEX SPX RAM Ver 47
>>>>>> K56FLEX CTL RAM Ver 47
>>>>>> ATI7 - 255
>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>
>