You need to replace the DSL Modem with the new Router.
Your DSL Modem isn't really a "modem" if it supplies DHCP,...that would mean
it is also a "router" in spite of what name they call in on the box. In
other words, both Devices are NAT Devices and are in direct competion to
each other. Off the top of my head I see these options.
Option 1
Use the WiFi Router in place of the current DSL Device and replace all the
Nics in your machines with wireless Nics,...unless there is a place on the
WiFi Device to plug in a "wired" hub or switch to tie your existing "wired"
machines into.
Option 2 (in my opinion the best option)
Take the Wifi Router back and exchange it for a Wireless Access Point (WAP).
These devices are simply the equivalent of a wireless hub or switch. They
do not do any "NAT" or "routing" or "DHCP",...they are no different than a
hub or switch other than they are wireless. You simply add them into the
existing LAN just as you would an additional computer. Any machines with
Wireless Nics would connect into the LAN by going through the WAP. The
existing "wired" portion of the LAN remains totally unchanged.
Option 3
I probably should say "non-option 3". You cannot put the two device in a
"series" because you will create a Back-to-Back DMZ between the new WiFi
device and the old wired DSL Device. This will cause your "wired" machines
to be in the DMZ which means they are "untrusted". Any WiFi machines will be
on what would become the new "LAN" on the wireless side. The WiFi machines
could access the wired side (in a limited way) but the wired side would be
"untrusted" and could not access the WiFi side.
The only solution to the above would be if the WiFi "router" can have NAT &
DHCP disabled and have some sort of "bridging" feature. The bridging would
cause both sides of the device to be the same subnet,...in other words it
would act just like the cheaper WAP I mentioned in Option 2. Another
possiblity was if it could act as a true "router" without "NAT",...but I
really doubt that would be the case.
In the end, it is always better to buy the proper hardware for the proper
job in the fisrt place.
--
Phillip Windell [MCP, MVP, CCNA]
www.wandtv.com
-----------------------------------------------------
Understanding the ISA 2004 Access Rule Processing
http://www.isaserver.org/articles/IS...cessRules.html
Microsoft Internet Security & Acceleration Server: Guidance
http://www.microsoft.com/isaserver/t...dance/2004.asp
http://www.microsoft.com/isaserver/t...dance/2000.asp
Microsoft Internet Security & Acceleration Server: Partners
http://www.microsoft.com/isaserver/partners/default.asp
-----------------------------------------------------
"Bob Bedford" <(E-Mail Removed)> wrote in message
news:(E-Mail Removed)...
> I've 1 ADSL modem (zyxel 650ME) wich is connected to internet.
> This ADSL modem is also a DHCP server and may serve up to 4 addresses.
> It's default IP configuration is 192.168.1.1
> It uses PPOe mode.
>
> I've just bought a LinkSys Wireless router. It has 4 ethernet ports and
> wireless access.
> It's default IP configuration is also 192.168.1.1
> this router has off course DHCP server enabled and may serve many more
> connections (up to 50), so I'm not limited to 4 addresses anymore.
>
> What I'm tring to do is configure the linksys as a DHCP server, wich does
> serve all my computers's addresses and not to use the modem DHCP feature.
> Problem is that I don't know how to set the modem later as it doesn't have
> any IP. I don't want 2 subnets, all computers must be visible in the same
> 192.168.1.X subnet.
>
> How to do so ? I'm quite a newbie in such networking stuffs.
> How to set up the modem. Should I disable DHCP, what IP set up to it ?
> How to set up the Wireless router ? with DHCP but wich IP ?
>
> Bob
>
>
>
>
Similar Threads
